Amit Kumar

Amit Kumar

Auto-generated profile, based on publicly available information

Amit Kumar

Department of Mechanical Engineering, National Institute of Technology, Patna, India

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 August 2017 in Ferroelectrics
Verified
Journal Article
Closed access
SPS. K. Pradhan
S. K. Pradhan
AKAmit Kumar
Amit Kumar
ASA. N. Sinha
A. N. Sinha
PKP. Kour
P. Kour
RPRabichandra Pandey
Rabichandra Pandey
MKManoranjan Kar
Manoranjan Kar
PVDF with 0, 2, 4, 6, 8, 10 mole% of PZT has been prepared by the solvent casting method. Prominent β phase has been observed from the XRD, FT-IR and Raman studies. The polarization of these samples starts at high field of 100 kv/cm and it increases with the increase in applied electric field. The 4 mole% PZT doped PVDF shows maximum polarization and high coercive field. The coercive field also increases with the increase in applied electric field. Hence, 4 mole% PZT doped PVDF composites can be used in high electric fields applications.

5 June 2022 in Advances in Materials and Processing Technologies
Verified
Journal Article
Closed access
Ajay MauryaAjay Maurya
Ajay Maurya
AKAmit Kumar
Amit Kumar
DMLS fabricated IN718 alloy samples with various build orientations are analysed with heat-treatment dependent mechanical and microstructural properties. The multiple heating and cooling cycles formed a complex micro-heterogeneous microstructure composed of columnar and equiaxed subgrains in the alloy. Solution treatment resulted in a partially dissolved δ phase, and the metastable γ” phase while ageing treatment eliminated the dendritic substructure. In contrast, δ-phases precipitated mainly in the interdendritic regions, and significantly eliminated the micro-segregation and Laves phases in the γ matrix after homogenised (HSA). . The tensile test showed that tensile strength decreased with increasing building orientation but ductility increased. Heat-treatment significantly improved the microhardness, ultimate tensile strength, and yield strength compared to the as-fabricated samples, but their ductility decreased. The tensile properties recorded an improvement of nearly 31.32% as compared to 0° as-built and 0° heat-treated direct aged samples. The higher microhardness (507.25 HV) was observed for the direct aged 0° build samples. The microhardness values were increased by nearly 45% after heat-treatment comparing to as-build 0° and 0° DA treated samples. The density was observed to be about 99.52% of the as-built samples, but performing the heat-treatment, no significant improvement in the density was observed and it was found similar to the as-fabricated sample.

14 December 2022 in AMB Express
Verified
Journal Article
Open access
PDF file
RMRavi Singh Manhas
Ravi Singh Manhas
AKAmit Kumar
Amit Kumar
ACAsha Chaubey
Asha Chaubey
Consistent production of bioactives from microbial sources remains a big challenge for fermentation based bio-processes. Setomimycin, a rare 9,9'-bianthrylanthracene antibiotic reported to be active against Gram positive bacteria i.e. Staphyloccocus aureus, Bacillus subtilis, Bacillus cereus, and Mycobacterium smegmatis, including mycobacteria is one of the least exploited antibiotic. Present work aims to enhance and maximize setomimycin production using One Factor at a Time (OFAT) approach, followed by Taguchi L9 orthogonal array (OA) design in 30L fermenter. Four most influential parameters, namely carbon source, nitrogen source, air and agitation were selected for optimization studies. The optimized production medium supplemented with 150 g/L glycerol and 7.5 g/L soyabean meal with an agitation rate of 100 RPM and air flow rate of 20 LPM (Liters Per Minute) resulted in 675 mg/L setomimycin production within 96–108 h of fermentation as compared to the initial production i.e. 40 mg/L. Thus, an overall enhancement of 16.8 folds was achieved in setomimycin production after optimization in 30L fermenter. Graphical Abstract

22 September 2026 in Journal of Advanced Manufacturing Systems
Verified
Journal Article
Closed access
PDF file
KAKumari Archana
Kumari Archana
AKAmit Kumar
Amit Kumar
PKPratibha Kumari
Pratibha Kumari