Yuya Takase

Prof. Yuya Takase


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2023 in Structures
Verified
Journal Article
Closed access
DSD. Suenaga
D. Suenaga
YTYuya Takase
Yuya Takase
TAT. Abe
T. Abe
GOG. Orita
G. Orita
SAS. Ando
S. Ando

4 March 2022 in Journal of Asian Architecture and Building Engineering
Verified
Journal Article
Open access
MMMiki Matsubayashi
Miki Matsubayashi
YTYuya Takase
Yuya Takase
MMMitsuo Mizoguchi
Mitsuo Mizoguchi
Recent Japanese earthquakes have severely damaged the nonstructural walls of many buildings. While nonstructural walls do not influence the seismic performance of a building, this damage can still sometimes cause buildings to be demolished or render their continued use impossible. Therefore, it is important that seismic designs take the seismic properties of nonstructural walls into consideration. Shear loading tests and FE analysis were conducted to investigate this phenomenon, which showed that shear strength decreased and crack width increased with wider rebar spacing. The FE analysis indicated that the discrete crack model evaluated the test results more adequately than the smeared crack model. In addition, the stress distribution was localized with wider rebar spacing. Therefore, it is thought that the shear strength decreased. Finally, a simple crack width prediction method was proposed. With this method, the rebar strain was calculated using the horizontal deformation of the walls. Using this method, the crack width could be reasonably estimated. It is believed that these findings will be useful for designing nonstructural walls with improved seismic performance.

22 June 2019 in Journal of Advanced Concrete Technology
Verified
Journal Article
Closed access
PDF file
UMUkyo Musya
Ukyo Musya
YKYuki Katagiri
Yuki Katagiri
YTYuya Takase
Yuya Takase
TATakahide Abe
Takahide Abe
KSKeita Sakamoto
Keita Sakamoto
KKKeichi Katori
Keichi Katori
When buildings are seismically retrofitted, new members are connected to existing members through a roughened concrete surface, which is created using a vibration drill. However, there are few studies on such roughened concrete. When the roughened concrete area ratio is small, bearing failure occurs. On the other hand, shear failure occurs when the roughened concrete area ratio is large. In this paper, the focus was on bearing failure. When the roughened concrete area ratios were 0.1 to 0.3, the failure mode was bearing failure. To evaluate shear strength, the shapes of roughened concrete were measured using a laser displacement sensor and 3D scanner. Moreover, shear loading tests were conducted. Finally, a shear strength formula was proposed considering the concrete compressive strength, Young’s modulus, and vertical projection area. By comparing the test results with the calculated values, it is concluded that the proposed formula estimated the test results well. Finally, this paper is an extension of the authors’ previous work [Musya et al., (2019). “Supported Strength Formula of Roughened Concrete Using Shape Measurement Value by 3D-scanner.” AIJ Journal of Technology and Design, 25(59), 55-60].

20 February 2019 in AIJ Journal of Technology and Design
Verified
Journal Article
Open access
PDF file
UMUkyo Musya
Ukyo Musya
YTYuya Takase
Yuya Takase
TATakahide Abe
Takahide Abe
KSKeita Sakamoto
Keita Sakamoto
THTakeshi Hiwatashi
Takeshi Hiwatashi
KKKeiichi Katori
Keiichi Katori
When buildings are seismically retrofitted, new members are connected to existing members by roughened concrete surface. However, there are few studies on roughened concrete. To evaluate the shear strength of the roughened concrete, the shapes of roughened concrete were measured using 3D scanner, then we conducted the shear loading tests. As a result, failure modes were supported failure and shear failure when rcr were respectively 0.1 to 0.3 and 0.5 to 1.0. This paper focused on supported failure, a shear strength formula constructed considering the concrete compressive and the vertical projection area. The proposed formula could estimate the test results.

19 February 2023 in Journal of Advanced Concrete Technology
Verified
Journal Article
Open access
PDF file
TYTaizo Yamada
Taizo Yamada
YTYuya Takase
Yuya Takase
TATakahide Abe
Takahide Abe
In seismically retrofitted reinforced concrete (RC) structures, new members are connected to existing members using interfaces with roughened surfaces and post-installed dowel bars. During an earthquake, the interfaces are subjected to cyclic shear and normal stresses. Therefore, the structural design of interfaces is essential. In a previous study, normal and shear loads were applied to interface specimens. Moreover, a shear strength estimation method was proposed; however, the cyclic behavior was not discussed. This paper presents a cyclic model of the roughened surface in retrofitted RC structures. First, an envelope model was constructed using the previous shear strength estimation method and Saenz model, a constitutive law of concrete. Subsequently, the cyclic rules were modeled. Moreover, a previous dowel model was incorporated into the proposed cyclic model to estimate the test results. Finally, the proposed model provided reasonably estimated test results; the average ratio of the test results to the model results was 1.04. In addition, as δ increased, the effect of the dowel bar intensified in terms of shear.

1 January 2020 in Journal of Structural and Construction Engineering (Transactions of AIJ)
Verified
Journal Article
Open access
PDF file
YIYutaro Ishida
Yutaro Ishida
HSHiroyasu Sakata
Hiroyasu Sakata
YTYuya Takase
Yuya Takase
YMYusuke Maida
Yusuke Maida
TSTakumi Sato
Takumi Sato
MKMasaharu Kubota
Masaharu Kubota
The disk shear-key is a composite shear resistance system composed of a steel disk and an anchor bolt. The disk shear-key has high stiffness and shear strength as compared with a general post-installed anchor. In the previous study, it is suggested that the expected shear strength can not be demonstrate when tensile force acts on the disk shear-key. Therefore, in the current design and construction method for the external seismic retrofitting, the disk shear-keys are placed in the center of the span and it is assumed that the shear force is to be borne on average. Then, for the tensile force due to the eccentric moment, post-installed anchors are placed at both ends of span. In order to make effective use of the disk shear-key, it is necessary to grasp the mechanical behavior under combined stress and arrange it efficiently. Therefore, in this study, the disk shear-key was tested under cyclic shear force along with constant tensile force. In Chapter 2, the outline of the experiment is indicated. The eight specimens were built with various parameters, which is, diameter of the steel disk Rd, embedded length of the anchor bolt le, and tensile force ratio η’. Here, the tensile force ratio is the ratio of the tensile axial force to the tensile strength of the disk shear-key. The experiment results are described in Chapter 3. The shear strength of the specimens in this experiment was less than the ultimate shear strength according to the current evaluation formula. This is considered to be caused by the different loading condition in the vertical direction from the previous experiment. When the vertical stress generated at the joint surface is zero (η’=0), the shear strength of the disk shear-key can be roughly estimated by the design shear strength according to the current design evaluation formula. However, in the range of η’=0 to 0.5 conducted in this experiment, the relative horizontal displacement of joint at maximum shear strength was within 2mm, which is the allowable value of the external seismic retrofitting joints. Also, the relative vertical displacement of joint increases as the tensile force is applied. Furthermore, in the case of application to external seismic retrofitting, the relative vertical displacement becomes large even when no tensile force is applied. It is suggested that the steel disk slips out, and it is believed that the shear resistance decreases due to the strength reduction in the bearing stress area of the concrete. In addition, the curvature of the anchor bolt is maximized at the position near 2da away from the joint surface on the existing side, and the value reaches the yielding region. However, curvatures within the elastic range occur at the other measurement points, and bending deformation hardly occurs at the retrofitting part. In Chapter 4, the shear strength evaluation formula under constant tensile force was constructed. The evaluation formula was modified in consideration of slipping out of the steel disk and the reduction of restraint effect by anchor bolt due to the tensile force. It was evaluated almost accurately with the experimental results.