Oleg Kashin

Oleg Kashin


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2020 in Metals
Verified
Journal Article
Open access
PDF file
OKOleg Kashin
Oleg Kashin
KKKonstantin Krukovskii
Konstantin Krukovskii
Aleksandr LotkovAleksandr Lotkov
Aleksandr Lotkov
VGVictor Grishkov
Victor Grishkov
The paper analyzes the microstructure and mechanical properties of Ti49.8Ni50.2 alloy (at.%) under uniaxial tension at room temperature after isothermal abc pressing to true strains e = 0.29 − 8.44 at T = 723 K. The analysis shows that as the true strain e is increased, the grain–subgrain structure of the alloy is gradually refined. This leads to an increase in its yield stress σy and strain hardening coefficient θ = dσ/dε at linear stage III of its tensile stress–strain curve according to the Hall–Petch relation. However, the ultimate tensile strength remains invariant to such refinement. The possible mechanism is proposed to explain why the ultimate tensile strength can remain invariant to the average grains size (dav). It is assumed that the sharp increase of the ultimate tensile strength σUTS begins when (dav) is less than the critical average grain size (dav)cr. In our opinion, for the investigated alloy (dav)cr ≈ 0.5 µm. In our study, the attained average grain size is larger the critical one. The main idea of the mechanism is next. In alloys with an average grain size (dav) less than the critical one, a higher external stress is required for the nucleation and propagation of the main crack.

20 July 2021 in Metals
Verified
Journal Article
Open access
PDF file
OKOleg Kashin
Oleg Kashin
Aleksandr LotkovAleksandr Lotkov
Aleksandr Lotkov
VGVictor Grishkov
Victor Grishkov
KKKonstantin Krukovskii
Konstantin Krukovskii
DZDorzhima Zhapova
Dorzhima Zhapova
EBElena Barmina
Elena Barmina
This paper presents experimental data on the microstructure and martensite transformation temperatures of Ti49.8Ni50.2 (at%) after abc pressing (multi-axial forging) to different true strains e from 1.84 to 9.55 at 573 K. The data show that increasing the true strain results in grain–subgrain refinement on different scales at a time. With e = 9.55 at 573 K, the average grain–subgrain size measured approximately 130 nm. Decreasing the abc pressing temperature from 723 to 573 K caused a decrease in all martensite transformation temperatures, a change in the lattice parameters, R phase formation, and angular shifts of diffraction peaks and their broadening. The largest change in the microstructure of Ti49.8Ni50.2 was provided by abc pressing to e = 1.84. Increasing the true strain to e = 9.55 resulted in a much smaller effect, suggesting that the alloy obtained a high density of structural defects even at e = 1.84. Two possible mechanisms of grain–subgrain refinement are discussed.

18 June 2022 in Metals
Verified
Journal Article
Open access
PDF file
Aleksandr LotkovAleksandr Lotkov
Aleksandr Lotkov
OKOleg Kashin
Oleg Kashin
VGVictor Grishkov
Victor Grishkov
DZDorzhima Zhapova
Dorzhima Zhapova
KKKonstantin Krukovskii
Konstantin Krukovskii
OKOlga Kashina
Olga Kashina
The mechanical properties of Ti49.8Ni50.2 (at %) alloy under tension at room temperature are studied in dependence on the true strain (e = 1.84–9.55) specified during isothermal multi-axial forging (abc-pressing). It was found that the stress at the beginning of the pseudoyield plateau does not depend on the value of the true abc-strain. It was found that after abs-pressing, already at a true strain e = 1.84, the yield stress σy was 900 ± 25 MPa, which is more than twice as high as compared to σy in the initial state of the specimens. With a further increase in the abc-strain, the yield stress continues to increase slightly and reaches 1000 ± 25 MPa at e = 9.55. In this case, the ultimate tensile strength of the samples increases by about 15%. The strain-hardening coefficient ϴ = dσ/dε at the III (linear) stage of the σ(ε) curve has a similar dependence on e. It is shown that after abc-pressing with e from 1.84 to 9.55, the yield stress and ultimate tensile increase linearly with increasing d−1/2 in accordance with the Hall–Petch relation, where d is the average grain–subgrain size.