Enrique E. Zayas-Figueras

Dr. Enrique E. Zayas-Figueras

Universitat Politècnica de Catalunya - Barcelona Tech, Spain
+1
orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

31 October 2009 in Mechanism and Machine Theory
Verified
Journal Article
Closed access
Enrique E. Zayas-FiguerasEnrique E. Zayas-Figueras
Enrique E. Zayas-Figueras
SCS. Cardona
S. Cardona
LJL. Jordi
L. Jordi

17 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
VMVitaliy Martynenko
Vitaliy Martynenko
Daniel Martinez KrahmerDaniel Martinez Krahmer
Daniel Martinez Krahmer
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
ACAmado Cabo
Amado Cabo
DPDaniela Pérez
Daniela Pérez
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
In the forging industry, surface quality and surface treatments of dies are crucial parameters to extend their life. These components are usually machined by milling or by Electrical Discharge Machining (EDM), and the final surface roughness depends on the machining techniques and operational conditions used in its fabrication. After milling, a nitriding treatment is widely applied to extend its service life. Nevertheless, no scientific report that informs about nitriding after EDM has been found. Accordingly, this work focuses on the wear and friction behavior of pins made of brass and medium carbon steel sliding over AISI H13 discs, made by wire EDM in the conditions of finishing and roughing. The discs are plasma nitride, and their effect on the wear during pin-on-disc tests is evaluated. In this sense, the analysis of the surface damage for the different pins will help us to understand the service life and wear evolution of the forging dies. The results show that plasma nitride reduces the friction and prevents the degradation of the pin, independently of the material of the pin, when sliding over finishing and roughing EDM conditions.

2 February 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
Enrique E. Zayas-FiguerasEnrique E. Zayas-Figueras
Enrique E. Zayas-Figueras
Irene Buj-CorralIrene Buj-Corral
Irene Buj-Corral
In this work, the design, manufacture and measurement process of constant-breadth cams is presented. The motion law of the cam was designed by means of Bézier curves and the corresponding design desmodromic constraints. The cams were manufactured in two different materials employing two different processes: PLA cams with fused filament fabrication (FFF) and aluminium cams with computer numerical control (CNC) milling. The main aim of this work is to compare both types of cams regarding dimensional accuracy and surface finish, in order to evaluate if it would be possible to temporally replace a metallic cam with a plastic one during the repair of the first one. Dimensions were measured with micrometres and surface roughness with a contact roughness meter. The results show that, in diametral dimensions, similar dimensional error values were obtained for both the 3D-printed and the machined cams. However, in longitudinal dimensions, whose direction is perpendicular to the 3D-printed layers, the 3D-printed cams showed higher dimensional error than the machined ones. The average roughness Ra in the 3D-printed cams was 20 times higher than in the milled cams. According to the results, it would be recommended to temporally replace metallic cams with plastic ones in applications of low-power transmission. Given that in the literature little information is available about the measurement of 3D-printed desmodromic cams, this work will contribute to the study and analysis of this kind of 3D printed mechanism.

26 May 2025 in Anales de Ingeniería Mecánica
Verified
Journal Article
Open access
PDF file
Enrique E. Zayas-FiguerasEnrique E. Zayas-Figueras
Enrique E. Zayas-Figueras
Irene Buj-CorralIrene Buj-Corral
Irene Buj-Corral
OSOt Godó Stany
Ot Godó Stany
En el presente trabajo se presenta la comparativa de parámetros dimensionales de engranajes cilíndricos de dientes helicoidales fabricados mediante la tecnología de fabricación por filamento fundido (FFF) con dos materiales poliméricos diferentes: el ácido poliláctico (PLA) y la poliamida (PA), comúnmente llamada Nylon. Se exponen el diseño y la modelación, mediante la biblioteca ToolBox de SolidWorks, de engranajes helicoidales con ángulos de hélice de 15, 25 y 35 grados respectivamente y, con un módulo y número de dientes considerados comunes (m= 4; z= 17) con ángulo de presión de 20 grados, que permite generar un perfil de diente evolvente correcto. Los engranajes modelados se materializan mediante una impresora de sobremesa BCN3D Sigma R19, utilizando los materiales antes indicados. Se presentan los métodos de medición de parámetros geométricos utilizados en la verificación de dichos engranajes, las metodologías a utilizar, así como los cálculos necesarios para realizar las mediciones y obtener los valores teóricos de referencia. La verificación de los engranajes impresos se hace mediante instrumentos como un pie de rey de módulo, un micrómetro de platillos, cilindros calibrados y pie de rey tipo Mauser. Se utilizaron tres métodos de verificación, que son: el método basado en el círculo de cabeza, el método de la distancia cordal y el método de medición basado en varillas calibradas respectivamente. El análisis de las medidas realizadas con los instrumentos de medida manuales indica que no existe un material que presente resultados significativamente mejores que otro respecto a los parámetros dimensionales considerados. Los resultados que se presentan en este trabajo surgen como parte del trabajo final de grado de uno de los autores del trabajo desarrollado en la Escola Tècnica Superior d’Enginyeria Industrial de Barcelona (ETSEIB) de la Universitat Politècnica de Catalunya (UPC).

27 August 2020 in Metals
Verified
Journal Article
Open access
PDF file
Irene Buj-CorralIrene Buj-Corral
Irene Buj-Corral
Enrique E. Zayas-FiguerasEnrique E. Zayas-Figueras
Enrique E. Zayas-Figueras
ÀMÀngels Montaña-Faiget
Àngels Montaña-Faiget
Cam-follower mechanisms are usually employed in different machines, like combustion engines, sewing machines, machine tools, etc. In the present paper, the option to manufacture cams utilizing wire electrical discharge machining (WEDM) has been considered. For this, surface roughness and shape error of cam profiles manufactured by the processes of milling and wire electrical discharge machining (WEDM) are presented. The methodology used covers different stages: design, prototyping, manufacturing, and measurement of the cams. As a reference, a cam-follower mechanism from a motorcycle internal combustion engine has been used. A reverse engineering process has been performed to determine the geometrical parameters of the mechanism, which are used for the synthesis of the profile of the cam and its subsequent design. The manufacturing process of the cams has been assisted by CAD-CAM (Computer Assisted Drawing-Computer Assisted Manufacturing) software. Using fused filament fabrication (FFF), a physical prototype of the cam has been manufactured, in order to validate the goodness of the design. Finally, the roughness and shape parameters have been measured on the contour surface of the cams. The arithmetical mean roughness Ra value of the milled cam was 0.269 μm, below the requirement of 0.4 μm, and shape error was 18 μm, below 50 μm. Shape error of the WEDM cam of 48 μm meets the requirements for cams. However, the Ra value of 1.212 μm, exceeded the limit. For this reason, a finish operation is recommended in this case. Some advantages of WEDM cams over milled cams are that different conductive materials can be employed, more complex shapes can be obtained, and that, in rough operations, the amount of material to be removed in subsequent operations is considerably reduced.