Amelia Nápoles Alberro

Dr. Amelia Nápoles Alberro

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 March 2016 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
SHSaqib Hameed
Saqib Hameed
HGHernán Alberto González
Hernán Alberto González
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro

25 May 2018 in Materials
Verified
Journal Article
Open access
PDF file
SHSaqib Hameed
Saqib Hameed
HGHernán Alberto González
Hernán Alberto González
JBJosé I. Perat Benavides
José I. Perat Benavides
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
In this article, the influence of electropulsing on the machinability of steel S235 and aluminium 6060 has been studied during conventional and electropulsing-assisted turning processes. The machinability indices such as chip compression ratio ξ , shear plane angle ϕ and specific cutting energy (SCE) are investigated by using different cutting parameters such as cutting speed, cutting feed and depth of cut during electrically-assisted turning process. The results and analysis of this work indicated that the electrically-assisted turning process improves the machinability of steel S235, whereas the machinability of aluminium 6060 gets worse. Finally, due to electropluses (EPs), the chip compression ratio ξ increases with the increase in cutting speed during turning of aluminium 6060 and the SCE decreases during turning of steel S235.

21 March 2019 in Materials
Verified
Journal Article
Open access
PDF file
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
HGHernán Alberto González
Hernán Alberto González
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
SHSaqib Hameed
Saqib Hameed
RAReyna M. Peña Aguilar
Reyna M. Peña Aguilar
Grinding energy efficiency depends on the appropriate selection of cutting conditions, grinding wheel, and workpiece material. Additionally, the estimation of specific energy consumption is a good indicator to control the consumed energy during the grinding process. Consequently, this study develops a model of material-removal rate to estimate specific energy consumption based on the measurement of active power consumed in a plane surface grinding of C45K with different thermal treatments and AISI 304. This model identifies and evaluates the dissipated power by sliding, ploughing, and chip formation in an industrial-scale grinding process. Furthermore, the instantaneous positions of abrasive grains during cutting are described to study the material-removal rate. The estimation of specific chip-formation energy is similar to that described by other authors on a laboratory scale, which allows to validate the model and experiments. Finally, the results show that the energy consumed by sliding is the main mechanism of energy dissipation in an industrial-scale grinding process, where it is denoted that sliding energy by volume unity decreases as the depth of cut and the speed of the workpiece increase.

17 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
VMVitaliy Martynenko
Vitaliy Martynenko
Daniel Martinez KrahmerDaniel Martinez Krahmer
Daniel Martinez Krahmer
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
ACAmado Cabo
Amado Cabo
DPDaniela Pérez
Daniela Pérez
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
In the forging industry, surface quality and surface treatments of dies are crucial parameters to extend their life. These components are usually machined by milling or by Electrical Discharge Machining (EDM), and the final surface roughness depends on the machining techniques and operational conditions used in its fabrication. After milling, a nitriding treatment is widely applied to extend its service life. Nevertheless, no scientific report that informs about nitriding after EDM has been found. Accordingly, this work focuses on the wear and friction behavior of pins made of brass and medium carbon steel sliding over AISI H13 discs, made by wire EDM in the conditions of finishing and roughing. The discs are plasma nitride, and their effect on the wear during pin-on-disc tests is evaluated. In this sense, the analysis of the surface damage for the different pins will help us to understand the service life and wear evolution of the forging dies. The results show that plasma nitride reduces the friction and prevents the degradation of the pin, independently of the material of the pin, when sliding over finishing and roughing EDM conditions.

26 June 2026 in International Journal of Mechanics and Materials in Design
Verified
Journal Article
Open access
PDF file
HGHernán Alberto González
Hernán Alberto González
Enrique E. Zayas-FiguerasEnrique E. Zayas-Figueras
Enrique E. Zayas-Figueras
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
EPErick D. Chávez Pereda
Erick D. Chávez Pereda
Antonio J. Sánchez EgeaAntonio J. Sánchez Egea
Antonio J. Sánchez Egea
This research introduces an approach, denoted as the Natural Coordinates Lagrangian Algorithm using the Steepest Descent Method ( $$NCLA_{sdm}$$ N C L A sdm ) for the dimensional synthesis of planar mechanisms with the objective of determining the required geometric dimensions for the generation of a desired path. The proposed approach utilizes a Lagrangian optimization method that employs the Steepest Descent Method and natural coordinates related by the constraint equations defining the admissible configurations of the mechanism. The proposed method is validated through the synthesis of four mechanisms of varying complexity. The numerical examples shown are slider-crank mechanisms with and without slider eccentricity, a four-bar mechanism, and the Theo Jansen linkage. The results demonstrate a strong agreement between the desired paths and those generated by the synthesized mechanisms, even in highly complex mechanisms such as those of Theo Jansen.

8 May 2014 in arXiv
Verified
Preprint
Open access
PDF file
Gisela Pujol-VázquezGisela Pujol-Vázquez
Gisela Pujol-Vázquez
Leonardo AchoLeonardo Acho
Leonardo Acho
AAAmelia Nápoles Alberro
Amelia Nápoles Alberro
Vega Pérez-GraciaVega Pérez-Gracia
Vega Pérez-Gracia
A Laboratory device is designed to emulate the Segway motion, modifying the Furuta pendulum experiment. To copy the person on the Segway transportation unit to the Furuta pendulum, a second pendulum is added to the main one. Using LMI theory, the control objective consists to manipulate the base of the Furuta pendulum according to the inclination of the added pendulum whereas the coupled pendulums are maintained near to theirs upright positions. According to the inclination of the second pendulum, the base will rotate as long as the second pendulum remains inclined, emulating the Segway behavior. The base rotation will depend on the side of the inclination too. Experimental results are offered too (video link: http://youtu.be/SHQdW3k3qiE).