During the last years, great progress was made in material science in terms of concept, design and fabrication of new composite materials with conferred properties and desired functionalities. The scientific community paid particular interest to active soft materials, such as soft actuators, for their potential as transducers responding to various stimuli aiming to produce mechanical work. Inspired by this, materials engineers today are developing multidisciplinary approaches to produce new active matters, focusing on the kinematics allowed by the material itself more than on the possibilities offered by its design. Traditionally, more complex motions beyond pure elongation and bending are addressed by the robotics community. The present review targets encompassing and rationalizing a framework which will help a wider scientific audience to understand, sort and design future soft actuators and methods enabling complex motions. Special attention is devoted to recent progress in developing innovative stimulus-responsive materials and approaches for complex motion programming for soft robotics. In this context, a challenging overview of the new materials as well as their classification and comparison (performances and characteristics) are proposed. In addition, the great potential of soft transducers are outlined in terms of kinematic capabilities, illustrated by the related application. Guidelines are provided to design actuators and to integrate asymmetry enabling motions along any of the six basic degrees of freedom (translations and rotations), and strategies towards the programming of more complex motions are discussed. As a final note, a series of manufacturing methods are described and compared, from molding to 3D and 4D printing. The review ends with a Perspectives section, from material science and microrobotic points of view, on the soft materials’ future and close future challenges to be overcome.

The rise of soft robotics opens new opportunities in endoscopy and minimally invasive surgery. Pneumatic catheters offer a promising alternative to conventional steerable catheters for safe navigation through the natural pathways without tissue injury. In this work, we present an optimized 6 mm diameter two-degree-of-freedom pneumatic actuator, able to bend in every direction and incorporating a 1 mm working channel. A versatile vacuum centrifugal overmolding method capable of producing small geometries with a variety of silicones is described, and meter-long actuators are extruded industrially. An improved method for fiber reinforcement is also presented. The actuator achieves bending more than 180° and curvatures of up to 0.1 mm⁻¹. The exerted force remains below 100 mN, and with no rigid parts in the design, it limits the risks of damage on surrounding tissues. The response time of the actuator is below 300 ms and therefore not limited for medical applications. The working space and multi-channel actuation are also experimentally characterized. The focus is on the study of the influence of material stiffness on mechanical performances. As a rule, the softer the material, the better the energy conversion, and the stiffer the material, the larger the force developed at a given curvature. Based on the actuator, a 90 cm long steerable catheter demonstrator carrying an optical fiber is developed, and its potential for endoscopy is demonstrated in a bronchial tree phantom. In conclusion, this work contributes to the development of a toolbox of soft robotic solutions for MIS and endoscopic applications, by validating and characterizing a promising design, describing versatile and scalable fabrication methods, allowing for a better understanding of the influence of material stiffness on the actuator capabilities, and demonstrating the usability of the solution in a potential use-case.

Phase-change material–elastomer composite (PCMEC) actuators are composed of a soft elastomer matrix embedding a phase-change fluid, typically ethanol, in microbubbles. When increasing the temperature, the phase change in each bubble induces a macroscopic expansion of the matrix. This class of actuators is promising for soft robotic applications because of their high energy density and actuation strain, and their low cost and easy manufacturing. However, several limitations must be addressed, such as the high actuation temperature and slow actuation speed. Moreover, the lack of a consistent design approach limits the possibility to build PCMEC-based soft robots able to achieve complex tasks. In this work, a new approach to manufacture PCMEC actuators with different fluid–elastomer combinations without altering the quality of the samples is proposed. The influence of the phase-change fluid and the elastomer on free elongation and bending is investigated. We demonstrate that choosing an appropriate fluid increases the actuation strain and speed, and decreases the actuation temperature compared with ethanol, allowing PCMECs to be used in close contact with the human body. Similarly, by using different elastomer materials, the actuator stiffness can be modified, and the experimental results showed that the curvature is roughly proportional to the inverse of Young’s modulus of the pure matrix. To demonstrate the potential of the optimized PCMECs, a kirigami-inspired voxel-based design approach is proposed. PCMEC cubes are molded and reinforced externally by paper. Cuts in the paper induce anisotropy into the structure. Elementary voxels deforming according to the basic kinematics (bending, torsion, elongation, compression and shear) are presented. The combination of these voxels into modular and reconfigurable structures could open new possibilities towards the design of flexible robots able to perform complex tasks.

In soft robotics, the ability to generate advanced kinematics is a necessary step toward any more sophisticated tasks such as microobject manipulation, locomotion, or configuration changes. To this end, herein, a modular voxel‐based methodology adaptable to any scale and with any soft transducer is presented. The methodology is implemented at the micrometer scale with a one‐step fabrication process. An innovative gray‐tone lithography method using the two‐photon polymerization of photosensitive poly(N‐isopropylacrylamide) hydrogel is developed to print the voxels. Bending, compression, and twisting voxels are designed, printed, and characterized. A voxel consists of an isotropically shrinking active material reinforced adequately with a passive pattern. Each elementary voxel deforms along one degree of freedom and is a building block for superstructures able of advanced kinematics. With a side length of 40 μm, the bending voxel achieves a bending angle of 25º or curvature of . The compression voxel reaches an actuation strain of 40%, and the twisting voxel bends up to 18º. Advanced kinematics are demonstrated by printing complex structures composed of multiple elementary voxels. Herein, a foundation toward soft microrobots capable of performing complex tasks is constituted.