High fidelity (Hi-Fi) piezoelectric single crystal stake actuators are presented in this work. They are made of multiple rectangular d32 mode lead-based relaxor ferroelectric (notably Pb(Zn1/3Nb2/3)O3-PbTiO3 (PZN-PT) and Pb(In0.5Nb0.5)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 (PIN-PMN-PT)) single crystals bonded along their long edges with the aid of compliant polymeric edge guides into a square or polygonal pipe-like construction. Due to the highly stable engineered domain structure and high piezoelectricity of single crystal active materials, the actuators exhibit large linear displacement responses with negligible (<1%) hysteresis. Prototypes of square-pipe stake actuators were first fabricated and their phase transformation curves under different applied voltages, axial compressive loads and temperatures were established. Based on the information obtained, a range of Hi-Fi stake actuators with external square cross-sections of 5 × 5 mm2, 7.5 × 7.5 mm2 and 10 × 10 mm2, each of 4 different overall lengths of 15, 28, 41 and 54 mm, were further designed and fabricated using either PZN-PT or PIN-PMN-PT single crystals (both with TRO ≈ 110–125 °C) of 0.4 mm in crystal thickness. The stroke for the longest stake actuator fabricated (L = 54 mm) reaches −58 µm at 240 V. The working conditions, over which these Hi-Fi stake actuators remain linear with negligible hysteresis, were established for a total load of up to 10 kg and use temperature of up to 40 °C.
High-authority piezoelectric actuator (HAPA) is a term used to describe high-performance piezoelectric actuators of relatively large displacement (≥50 μm) and high blocking force (≥100 N), but compact in size. One such piezoelectric actuator is described in this paper, which is made possible by means of high-bending-stiffness connector (HBSC) that connects multiple commercial piezoceramic stacks into a stable 2- (or multi-) level actuation configuration. Key design requirements for the HBSC are described. Computer simulation results and experimental verification are presented. A HAPA-(2 + 2) actuator was fabricated from such a HBSC, in which there are two commercial PZT stacks projecting upwards in the upper level and two projecting downwards in the lower lever, all of 5 × 5 mm2 in cross-section and 40 mm in length. The HAPA-(2 + 2) actuator prototype displays about twice the overall stroke and blocking force of individual stacks, being about 90 μm and >1600 N, respectively. This compares favorably with lever-arm, flextensional, and telescopic actuators, of which the blocking force is adversely affected. Using a similar concept, HBSCs and HAPAs of other designs are presented. In addition to being stand-alone actuators, the HAPAs can be used as the active material to drive existing displacement amplification schemes to produce piezoelectric actuators of exceptional performance characteristics.
“Hi-Fi Stake” piezoelectric actuators are constructed by bonding [011]-poled d32-mode lead-based relaxor-PT single crystals with polycarbonate edge guides into a square-pipe structure. They contract under positive-polarity applied voltage due to d32 values being negative for [011]-poled relaxor-PT single crystals. Under quasi-static loading conditions, Hi-Fi Stake single crystal actuators exhibit highly linear displacement response with negligible hysteresis. Over the years, we have successfully developed the following three versions of Hi-Fi Stake (HFS) actuators: cost-effective (CE), large-stroke (LS) and high-load (HL), all of maximum use temperature of up to 60 °C. Of which, the LS version, of 2-level construction, displays strokes of up to 50 μm @ 240 V and the HL version, of 2-layer construction, has maximum loads allowed of 14 kg-f at room temperature and 7 kg-f at 60 °C. Additionally described in this work are the developments of Cryogenic Hi-Fi Stakes (CG-HFS) and High-Temperature Hi-Fi Stake (HT-HFS) actuators. The selection of suitable crystal compositions, recommended working conditions and measured performance of fabricated prototypes of these two new versions of Hi-Fi Stakes are presented and discussed.
“HAPA” stands for High-Authority Piezoelectric Actuator, which describes high-performance piezoelectric actuators of large stroke and blocking force. “HAPAs” are made possible by high-bending-stiffness connectors that connect multiple units of piezoceramic stacks into a 2-level actuation structure. Present HAPA actuators are fitted with commercial piezoceramic stacks. For instance, a “HAPA-(2+2)” comprises 4 lead zirconate titanate (PZT) stacks, 2 in the upper level with displacement projecting upward and 2 in the lower level with displacement projecting downward. They not only double the axial displacement of individual stacks with only fractional increase in device length but also are of 1.5 to 3 larger blocking force depending on the actual design. “FTA” stands for Flextensional Actuator, in which the horizontal extensional displacement of PZT stacks is amplified to yield much larger contractional vertical displacement via a diamond-shaped elastic frame structure. A range of new FTAs has been developed by us using single or multiple units of PZT stacks, of which the performances are described in this work. “HD-FTA” stands for HAPA-Driven Flextensional Actuator, in which HAPA piezoelectric actuators are used as the motor section to drive diamond-shaped elastic members of various designs for further displacement amplification. Several HD-FTAs, driven by a HAPA-(2+2) actuator, have been developed. Compared with standard FTAs of comparable stroke, HD-FTAs display a higher working load but of smaller overall length. “HAPA”, “FTA”, and “HD-FTA” piezoelectric actuators find applications when a smaller actuator length is advantageous in addition to the required moderate-to-large displacement and working load.