Results of tests into the energy-efficiency of belt conveyor transportation systems indicate that the energy consumption of their drive mechanisms can be limited by lowering the main resistances in the conveyor. The main component of these resistances is represented by belt indentation rolling resistance. Limiting its value will allow a reduction in the amount of energy consumed by the drive mechanisms. This article presents a test rig which enables uncomplicated evaluations of such rolling resistances. It also presents the results of comparative tests performed for five steel-cord conveyor belts. The tests involved a standard belt, a refurbished belt and three energy-saving belts. As temperature significantly influences the values of belt indentation rolling resistance, the tests were performed in both positive and negative temperatures. The results indicate that when compared with the standard belt, the refurbished and the energy-efficient belts generate higher and lower indentation rolling resistances, respectively. In order to demonstrate practical advantages resulting from the use of energy-saving belts, this article also includes calculations of the power demand of a conveyor drive mechanism during one calendar year, as measured on a belt conveyor operated in a mine. The replacement of a standard belt with a refurbished belt generates a power demand higher by 4.8%, and with an energy-efficient belt—lower by 15.3%.

Damage detection in complex mechanical structures is important for cost-effective and safe operation. Conveyor belts with steel cords are used for bulk material transport in mining companies. Due to harsh environmental conditions, both covers and cords are subjected to damage. As lengths of conveyors may vary from dozens of meters to kilometers, a belt loop consists of many connected belt pieces. Thus, the condition of splices between belt pieces is also critical. For both steel cord damage/wear detection and splice condition evaluations the NDT techniques based on magnetic field measurement and variability analysis are used. To obtain appropriate resolution, multi-channel data are collected. Here we propose a pre-processing technique developed for signal synchronization for biased splices data. The biased splices mean a phase shift between signals from a multi-channel sensor due to the design technology of the splice. As the quality of the splice is related to the appropriate precision of splice production, splice evaluation is defined as a similarity analysis of each signal with respect to the estimated pattern. Due to the mentioned phase shift, signals should be "synchronized" first, before final analysis. In industrial conditions, many factors may influence the signal shape. Thus, the problem of automated synchronization by shifting the signals may be defined as a multidimensional optimization problem. Here, we proposed to use a genetic algorithm with an algorithmically simple cost function for that purpose. In this paper, the authors propose an automated procedure applied to real measurement data and final results. A multidimensional optimization has been compared to simple signal shifting according to several criteria, and GA-based results were the best.

Belt conveyors are used for the transportation of bulk materials in a number of different branches of industry, especially in mining and power industries or in shipping ports. The main component of a belt conveyor is its belt, which serves both as a support for the transported material along the conveyor route and as an element in the drive transmission system. Being crucial to the effective and reliable operation of the conveyor, the belt is also its most expensive and the least durable element. A conveyor belt comprises a core, covers and edges. A multiply textile belt, in which the core is constructed of synthetic fibers such as polyamide, polyester or aramid, is the oldest and still the most commonly used conveyor belt type. The plies are joined with a thin layer of rubber or another material (usually the material is the same as the material used in the covers), which provides the required delamination strength to the belt and allows the plies to move relative to each other as the belt is bent. Belts are installed on the conveyors in a closed loop in order to join belt sections, whose number and length depend on the length and type of the belt conveyor. Belts are joined with each other in a splicing procedure. The cutting of the belt core causes belt splices to be prone to concentrated stresses. The discontinued core also causes the belt to be the weakest element in a conveyor belt loop. The article presents the results of strength parameter tests that were performed on laboratory and industrial splices and indicated the reasons for the reduced strength of conveyor belt splices. Splice strength is reduced mainly due to incorrect preparation of the spliced surfaces and to different mechanical parameters of the spliced belts.

Belt conveyors are presently the most common transportation machines used in surface and underground mining

Breaks in the so-called “continuous” (unspliced) belt sections, and not in the spliced areas, are infrequent but do happen in practice. This article presents some aspects, which may account for such breaks in conveyor belts. It indicates the so-called “sensitive points” in design, especially in the transition section of the conveyor belt and in identifying the actual strength of the belt. The presented results include the influence of the width of a belt specimen on the identified belt tensile strength. An increase in the specimen width entails a decrease in the belt strength. The research involved develops a universal theoretical model of the belt on a transition section of a troughed conveyor in which, in the case of steel-cord belts, the belt is composed of cords and layers of rubber, and in the case of a textile belt, of narrow strips. The article also describes geometrical forces in the transition section of the belt and an illustrative analysis of loads acting on the belt. Attention was also devoted to the influence of the belt type on the non-uniform character of loads in the transition section of the conveyor. A replacement of a conveyor belt with a belt having different elastic properties may increase the non-uniformity of belt loads in the transition section of the conveyor, even by 100%.

As steel cord conveyor belts are vulcanized during the production process, rubber penetrates into steel cords. It is a positive and a desired phenomenon allowing the belt to reach its required properties and ensuring its reliable and long operation on the belt conveyor. Advantageously, the rubber...