The petroleum industry plays a vital role in the economies of developing countries. Refinery wastewater pollution has increased in recent years due to the increase in the industrial and urban use of petroleum products. The present work demonstrates how textile waste can be modified into a material that can effectively remove sulfur pollutants from refinery wastewater. An economic activated carbon (AC) material was developed by using cotton spinning waste from a textile company. The chemical activation was carried out using nitric acid (HNO₃), hydrogen peroxide (H₂O₂), and potassium hydroxide (KOH). The characterization of the obtained activated carbons was performed using the SEM, BET, and FTIR techniques. The effect of the experimental adsorption condition was investigated using both bed and batch isotherms. The results show that effluent flow has the highest effect on sulfur compound adsorption. The greatest adsorption capacity of the sulfur compounds was found to be around 168.4 mg·g⁻¹. The equilibrium data were investigated using the Freundlich, Langmuir, Dubinin–Radushkevich, Tóth, and Sips isotherm models. The Langmuir model exhibited the best fit (R² = 0.98) for the sulfur compounds’ adsorption, which implies that their adsorption onto the synthesized AC was homogeneous. The kinetic data were tested with pseudo-first-order, pseudo-second-order, and intraparticular diffusion equations. The pseudo-second-order equation described the kinetic data well (R² = 0.99), indicating that this adsorption may be restricted by the chemisorption process. These properties under optimal conditions make the obtained ACs suitable for use in refinery wastewater treatment.

Cotton is one of the most-used natural fibres in the world due to its relative comfort and strength compared with other natural fibres. However, the processing of cotton for manufacturing products consumes a lot of water, while harvesting cotton uses significant amounts of pesticides. One solution to this ecological problem is to recycle cotton waste. This study investigated the effect of blending virgin cotton with two categories of denim cotton waste—sourced during the winding and dyeing processes and used in various ratios—on the quality of blended denim cotton. The study was realised in collaboration with a large manufacturer of denim fabrics in Tunisia and a producer of preparation machines in Italy and aimed to use an adequate process to recycle cotton yarn waste and to obtain fibres with acceptable quality. The research aimed at providing a solution to the great demand for denim with the use of reclaimed fabric, which accompanies the increased need for denim with a fancy effect and the obligation of denim producers to follow environmental standards required by many brands The results show that it is possible to obtain a good quality of blend yarn using virgin cotton and cotton waste even when the waste content exceeds 50%. These results are significant for textile mills. Reprocessing fibres from denim colour-processing waste has a lot of advantages, including reductions in wastewater treatment and the consumption of energy, chemicals and water. In addition, the process eliminates the need for the dyeing and finishing processes of these coloured fibres.

The primary objective of this paper is to compare the sorption characteristics of hydroxypropylmethylcellulose (HPMC) and hard gelatin (HG) capsules and their ability to protect capsule contents. Moisture sorption and desorption isotherms for empty HPMC and HG capsules have been investigated using dynamic vapour sorption (DVS) at 25°C. All sorption studies were analysed using the Young-Nelson model equations which distinguishes three moisture sorption types: monolayer adsorption moisture, condensation and absorption. Water vapour diffusion coefficients (D), solubility (S) and permeability (P) parameters of the capsule shells were calculated. ANOVA was performed with the Tukey comparison test to analyse the effect of %RH and capsule type on S, P, and D parameters. The moisture uptake of HG capsules were higher than HPMC capsules at all %RH conditions studied. It was found that values of D and P across HPMC capsules were greater than for HG capsules at 0-40 %RH; whereas over the same %RH range S values were higher for HG than for HPMC capsules. S values decreased gradually as the %RH was increased up to 60% RH. To probe the effect of moisture ingress, spray dried lactose was loaded into capsules. Phase evolution was characterised by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and differential scanning calorimetry (DSC). The capsules under investigation are not capable of protecting spray dried lactose from induced solid state changes as a result of moisture uptake. For somewhat less moisture sensitive formulations, HPMC would appear to be a better choice than HG in terms of protection of moisture induced deterioration.

Vertically-oriented zinc oxide (ZnO) nanowires were synthesized on glass and silicon substrates by Pulsed Laser Deposition and without the use of a catalyst. An intermediate c-axis oriented nanotextured ZnO seed layer in the form of nanowall network with honey comb structure allows the growth of high quality, self-forming, and vertically-oriented nanowires at relatively low temperature (5 Torr). Many parameters were shown to affect the growth of the ZnO nanowires such as gas pressure, substrate–target distance, and laser energy. Growth of a c-axis-crystalline array of nanowires growing vertically from the energetically favorable sites on the seed layer is observed. Nucleation occurs due to the matching lattice structure and the polar nature of the ZnO seed layer. Morphological, structural, and optical properties were investigated. X-ray diffraction (XRD) revealed highly c-axis aligned nanowires along the (002) crystal plane. Room temperature photoluminescence (PL) measurements showed a strong and narrow bandwidth of Ultraviolet (UV) emission, which shifts to lower wavelength with the increase of pressure.