To achieve an efficient conductive network while preserving the properties of carbon nanofillers is a challenging and essential issue for the fabrication of highly conductive polymeric nanocomposites. The present paper reports a facile approach to manipulate the network formation in the polymer matrix via introducing the tetrapod ZnO whisker (T-ZnO) in the carbon nanotube (CNT)-reinforced epoxy composite. The influence of T-ZnO on the CNT dispersion was evaluated by UV-Vis spectroscopy, rheological measurement, scanning electron microscopy (SEM), and electrical and mechanical properties of the bulk composite. The results showed that the CNTs tend to disperse more uniformly with an increase in T-ZnO loading. An optimized ratio of 1:2 between CNTs and T-ZnO was found to significantly enhance the electrical conductivity by 8 orders of magnitude. A low percolation threshold of 0.25 wt% CNTs was achieved in this hybrid CNTs/T-ZnO composite, which is only 40% of the threshold value in the pure CNTs/epoxy. The flexural strength and modulus of the hybrid composite were also improved noticeably in comparison to the CNTs/epoxy. The mechanism for increasing the performance of the nanocomposite was analyzed. These results indicated that the T-ZnO can assist to efficiently improve the dispersion and the formation of the conductive network, which is beneficial to the enhancement of the mechanical and electrical performance of the nanocomposite.
To enhance the understanding of airflow characteristics in the human respiratory tract, the inspiratory airflow field was simulated under both tidal and quasi-steady inspiratory flow rates at the mouth inlet using the large eddy simulation method. Special attention was paid on analyzing the inspiratory airflow unsteadiness using the dynamics mode decomposition (DMD) method based on the vorticity field and comparing it with the proper orthogonal decomposition (POD) method. The following novel findings were obtained. (1) Power spectral density indicates that the inspiratory airflow is highly turbulent in the pharynx–larynx region. The vorticity field in the upper airway is more affected by inspiratory patterns compared to turbulence fluctuations. (2) The DMD results indicate that the shear flow in the pharynx–larynx region is mainly caused by flow under low-frequency modes, while the disturbances of the jet flow are caused by flow under multiple frequency modes. Steady-state inspiratory pattern demonstrates the decay characteristics different from the tidal inspiratory pattern. (3) Compared to the POD method, which may contain multiple frequency components, the DMD decomposition yields modes with a single frequency, enabling a more accurate capture of the frequency and decay characteristics of the respiratory flow under each mode. In conclusion, this study demonstrates that the DMD method is more suitable for studying the respiratory airflow unsteadiness and further confirms the necessity of adopting clinically measured inspiratory data to investigate airflow unsteadiness.
A new predefined time sliding mode control theme is proposed and applies to the multi-switch combination–combination synchronization (MSCCS) of fractional-order (FO) hyperchaotic systems. Firstly, based on the Lyapunov stability theory, we demonstrate the effectiveness of our proposed predefined time sliding mode control theme. Meanwhile, based on the new predefined time control strategy, we propose new sliding mode surfaces and controllers to achieve the MSCCS of FO hyperchaotic systems. Considering the system’s external environment’s complexity in practical applications, the parameter uncertainties and external disturbances are added to the FO hyperchaotic system. Through the final numerical simulation, the predefined time slide mode controller proposed in this paper can make the drive–response systems reach the predefined time synchronization, thus proving the effectiveness of the control strategy and its robustness to some unfavorable factors, such as external perturbations.
In high-speed parachuting, complex turbulent phenomena (i.e., deadly vortices) may cause problems such as parachute inflation delay or even deployment failure. To address these issues, this study develops a high-precision numerical simulation dummy model in which adaptive mesh generation techniques, combined with Euler–Lagrange bidirectional coupling based on a large eddy simulation, are employed to model the multiphase flow field during parachute descent. The key parameters are adjusted, and the numerical model is refined based on wind tunnel experiments and User-Defined Functions. The bidirectional validation of the experimental and simulated data reveals the mechanism of turbulent flow formation and its evolutionary patterns around the parachutist–parachute system for different lateral and descent velocities during the high-speed descent phase. A prediction model based on a multi-information fusion neural network algorithm is further established to address the challenge in special parachuting scenarios whereby vortices in the flow field around the parachutist prevent the parachute from opening. The model integrates the Haar wavelet to extract global low-frequency features that characterize the overall structure and trends, an energy valley optimization algorithm, a convolutional neural network, a bidirectional long short-term memory network, and a self-attention mechanism to achieve one-second-ahead turbulence prediction. With nine physical quantities as inputs and descent velocity as the output indicator, the model has a Root Mean Square Error of 0.085, a Mean Absolute Error of 0.051, and a Mean Absolute Percentage Error of 0.0021.