Saurabh Kumar Gupta

Mr. Saurabh Kumar Gupta

Indian Institute of Science Bangalore, Bengaluru, India
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2021 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
SGSaurabh Kumar Gupta
Saurabh Kumar Gupta
NSNagur Shahidsha
Nagur Shahidsha
SBSumit Bahl
Sumit Bahl
DKDhaval Kedaria
Dhaval Kedaria
SSSarat Singamneni
Sarat Singamneni
KCKaushik Chatterjee
Kaushik Chatterjee

29 April 2022 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
DMDIKSHA PRAKASH MAHADULE
DIKSHA PRAKASH MAHADULE
Rajesh KhatirkarRajesh Khatirkar
Rajesh Khatirkar
SGSaurabh Kumar Gupta
Saurabh Kumar Gupta
Aman GuptaAman Gupta
Aman Gupta
Tushar DandekarTushar Dandekar
Tushar Dandekar

1 January 2021 in Renewable Energy
Verified
Journal Article
Closed access
SGSaurabh Kumar Gupta
Saurabh Kumar Gupta
SCShikhar Choudhary
Shikhar Choudhary
SKSuraj Kumar
Suraj Kumar
SDSantanu De
Santanu De


13 January 2015 in International Journal of Engine Research
Verified
Journal Article
Open access
PAPreeti S Abraham
Preeti S Abraham
XYXiaofeng Yang
Xiaofeng Yang
SGSaurabh Kumar Gupta
Saurabh Kumar Gupta
TKTang-Wei Kuo
Tang-Wei Kuo
DRDavid L Reuss
David L Reuss
VSVolker Sick
Volker Sick
Cycle-to-cycle variability of intake-jet flow in an optical engine was measured using particle image velocimetry, revealing the possibility of two different flow patterns. A phase-dependent proper orthogonal decomposition analysis showed that one or the other flow pattern would appear in the average flow, sampled from test to test or sub-sampled within a single test; each data set contained individual cycles showing one flow pattern or the other. Three-dimensional velocity data from a large-eddy simulation of the engine showed that the particle image velocimetry plane cuts through a region of high shear between the intake jet and another large flow structure. Rotating the measurement plane ±10° revealed one or the other flow structure observed in the particle image velocimetry measurements. Thus, it was hypothesized that cycle-to-cycle variations in the swirl ratio result in the two different flow patterns in the particle image velocimetry plane. Having an unambiguous metric to reveal large-scale flow cycle-to-cycle variability, causes for this variability were examined within the possible sources present in the available testing. In particular, variations in intake-port and cylinder pressure, lateral valve oscillations, and engine RPM were examined as potential causes for the cycle-to-cycle flow variations using the phase-dependent proper orthogonal decomposition coefficients. No direct correlation was seen between the intake-port pressure, or the pressure drop across the intake valve, and the in-cylinder flow pattern. A correlation was observed between dominant flow pattern and cycle-to-cycle variations in intake-valve horizontal position. RPM values and in-cylinder flow patterns did not correlate directly. However, a shift in flow pattern was observed between early and late cycles in a 2900-cycle test after an approximately 5 r/min engine speed perturbation.

Verified
Journal Article
Open access
PDF file
RSRishabh Soni
Rishabh Soni
Suyog JhavarSuyog Jhavar
Suyog Jhavar
STSuhela Tyeb
Suhela Tyeb
SGSaurabh Kumar Gupta
Saurabh Kumar Gupta
SSSatyam Suwas
Satyam Suwas
KCKaushik Chatterjee
Kaushik Chatterjee
Wire arc additive manufacturing (WAAM) offers a high rate of material deposition among various additive manufacturing techniques with wire as feedstock material but has not been established for zinc alloys. Zn alloys can be used as degradable biomaterials, in contrast to conventional permanent metallic biomaterials. In this work, commercially pure Zn was processed by WAAM to obtain near-dense parts, and the properties obtained through WAAM-processed Zn were compared with wrought (WR) Zn samples. The microstructure and hardness values of the WAAM (41 ± 1 HV0.3) components were found to be similar to those of the WR (35 ± 2 HV0.3) components. Bulk X-ray diffraction texture measurements suggested that WAAM builds exhibit a heavily textured microstructure compared to the WR counterparts, with peak intensities around or in the directions parallel to the build direction (BD). The corrosion rates in simulated body fluid (SBF) were similar for WAAM (0.45 mmpy) and WR (0.3 mmpy) samples. The weight loss measurements in SBF were found to be marginally higher in the WAAM samples compared to the WR counterparts for a duration of up to 21 days. MC3T3-E1 preosteoblasts were found to be healthy and proliferating in the culture medium containing the degradation products from WAAM-Zn in a manner similar to WR-Zn. This work establishes the feasibility of processing Zn by WAAM for use in bioresorbable metallic implants.