The performed investigations were focused on analysing the variability of geological-engineering properties in clay soils from central-eastern Europe with regard to microstructures. Thirty-nine soils differing in origin, lithology and microstructure type were selected for analysis. Results of studies on lithological and physical and mechanical parameters were analysed, coupled with quantitative microstructural parameters based on microstructure images. The relationships between lithological, physical and mechanical and pore space parameters were determined with regard to microstructure types. Sediment origin and diagenesis, and soil microstructure and pore space parameters had influence on the geological-engineering properties. Such approach allows for predicting engineering parameters based on soil microstructure types and their pore space parameters.

The paper presents the basic problem related with practical application of carbonate rocks in construction: are carbonate aggregates produced from such rocks favorable for building engineering, particularly for road design and construction? To resolve this problem, (1) the geological-engineering properties of aggregates are presented, (2) the correlation between petrographic and engineering parameters is shown, and (3) a strict correlation between the geological-engineering properties and the freezing-thawing and crushing resistance is recognized. This knowledge has allowed to assess the usefulness of asphalt concrete (AC) made from dolomite and limestone aggregates in the design and construction of road surface structures. The petrography was characterized using optical microscopy and scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectroscope (EDS). Engineering properties were determined in accordance with European and Polish norms and guidelines. Statistical and design calculations were performed using dedicated software. The petrographic properties, and selected physical and mechanical parameters of the aggregates, were tested to show their influence on the freezing–thawing and crushing resistance. Strong functional relationships between the water adsorption, and the freezing–thawing and crushing resistance have been observed. Aggregate strength decreased after saturation with increasing concentrations of salt solutions. Calculations of AC fatigue durability and deformation allow for reducing the thickness of the road surface structure by about 20% in comparison to normative solutions. This conclusion has impact on the economy of road design and construction, and allows for a rational utilization of rock resources, which contributes to sustainable development of the construction industry.

Faience objects produced from the fourth millennium BC in ancient Egypt are considered as the first high-tech ceramics in human history. Despite extensive studies on manufacturing technology, many aspects of this complex technology remain a mystery and there is no methodology in place to unravel the techniques of Egyptian faience object production. Detailed studies presented herein fill the gaps, verifying standing opinions and allowing certain aspects of faience manufacturing technology to be reconstructed. The object of this innovative investigation is a hemispherical faience bowl discovered by archaeologists excavating a Ptolemaic workshop district at the site of Tell Atrib in the southern Nile Delta. The multiproxy analysis included the application of specialised software and preparation techniques coupled with complementary methods of light and digital microscopy, SEM with EDS, XRD, STA with EGA, as well as image analysis. Sources of raw and accessory materials (mineral and organic binders, fluxes, colourants) used for preparing the silica paste and glaze slurry were determined. The results helped to reconstruct how the raw material was prepared and how faience vessels were made. The bowl was moulded by compression using a two-part mould. The moulded and dried bowl was then covered by glaze slurry using the application method. A synthetic colourant, Egyptian Blue, was probably used to colour the glaze. The item was fired once at a temperature of 1050–1150 °C. Oxidised conditions were maintained in the kiln during the firing process and firing at the maximal temperature was relatively short. Application of the multiproxy approach has shed light on the technological aspects of faience bowl manufacturing. The obtained results have confirmed the usefulness of the comprehensive methodology that was applied for the reconstruction of particular manufacturing stages of faience objects.

This article presents the results of petrophysical analyses of limestones and sandstones used for the construction of the wall structures of a Roman rural settlement located in Podšilo Bay on Rab Island (Croatia). An on-site analysis of the walls indicated the use of different lithotypes, which is an uncommon case in the area. So far, no petrophysical properties of the applied materials have been tested, and their provenance has not been specified. The aim of this research was to determine their usability as construction materials in an attempt to determine the possible reasons behind the usage of multiple lithotypes and their suitability as building materials. The following procedure was used to address these issues: (1) determination of the petrographic characteristics of the rocks, (2) performance of tests to characterise the mechanical properties in a complex stress state of uniaxial tension followed by uniaxial and triaxial compression, and, finally, (3) determination of the internal structure of the rocks using methods based on X-ray imaging. Multi-proxy characteristics of the materials including numerous observations and methods were performed: optical microscopy used to characterise rock petrography and mineralogy, scanning electron microscopy (SEM) coupled with EDS, as well as grinding tests; furthermore, mechanical properties were determined on cylindrical samples in accordance with European standards. X-ray microtomography using the XμCT method enabled microscopic observations and determination of the orientation of discontinuities and the rock structure. The performed analyses allowed us to distinguish three lithological types of sandstone and two types of limestone among the examined stone blocks. Stone blocks of fine- and medium-grained sandstone with carbonate binders, as well as sparitic limestone and mudstone with calcite veins, were used to build the studied structures. The analysed blocks showed traces of partial edge processing. Despite the defects in the material structure identified using XμCT, all the types of rock were characterised by high or very high strength. High values of longitudinal wave velocity confirmed the good quality of the material. These results contribute to a better understanding of the construction process and the related technological choices, and they provide the first dataset which can be used for the reconstruction of the building’s original appearance in the future.

The provenance of siliceous grain material, the basic source of manufacturing faience items, is still a matter of discussion. The study methods applied so far have not brought satisfactory outcomes, and the results are ambiguous and problematic. Archaeological evidence has also not supplied adequate proof for establishing the sites where the source material was obtained and the methods of its preparation. Therefore, we propose an interdisciplinary approach to solve these research problems. We explore selected material of 7 faience bowls precisely dated on the c. 100 years of the Ptolemaic Period in Egypt. The body and glaze of the faience bowls was qualitatively and quantitatively tested with regard to chemical and mineral composition, and selected material parameters. Based on structural-textural analysis, as well as chemical and mineral composition, the source area of the studied raw material and its potential excavation site was determined in the Eastern Desert. The obtained results were compared with locations of mines exploiting gold-bearing quartz veins, functioning in the Ptolemaic Period. Material parameters obtained from image analysis have been applied to reconstruct the processes of crushing and grinding of the quartz material and its further treatment for faience manufacturing. Quartz treatment was analysed with regard to tools and handling processes applied in Ptolemaic mines. We assume that such an approach has given accurate results in determining the provenance of siliceous material used in the Ptolemaic workshops of Athribis. Therefore, in material studies of artefacts produced in the antiquity, it is indispensable to use an interdisciplinary and complex approach, beginning from field studies and ending with detailed laboratory analyses.