Yeongjun Kim

Dr. Yeongjun Kim

Hanyang University Erica Campus
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 February 2020 in Scientific Reports
Verified
Journal Article
Open access
PDF file
Yeongjun KimYeongjun Kim
Yeongjun Kim
XWXinwei Wu
Xinwei Wu
JOJe Hoon Oh
Je Hoon Oh
Surface modification of polyimides (PIs) using electrospinning would significantly improve the performance of TENGs because of the larger surface area of the electrospun friction layer. However, PIs generally have high solvent resistance, so it is complicated to convert them into nanofibers using electrospinning process. This study aims to fabricate PI nanofibers via simple, one-step electrospinning and utilize them as a friction layer of TENGs for better performance. PI nanofibers were directly electrospun from PI ink made of polyimide powder without any additional process. The effect of PI concentration on spinnability was investigated. Uniform and continuous nanofibrous structures were successfully produced at concentrations of 15 wt% and 20 wt%. Electrospun PI nanofibers were then utilized as a friction layer for TENGs. A TENG with 20 wt% produced an open circuit voltage of 753 V and a short circuit current of 10.79 μA and showed a power density of 2.61 W m−2 at a 100 MΩ load resistance. During tapping experiment of 10,000 cycles, the TENG could stably harvest electrical energy. The harvested energy from the proposed TENG is sufficient to illuminate more than 55 LEDs and drive small electronic devices, and the TENGs exhibit excellent performance as a wearable energy harvester.

4 April 2016 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
SJShin Jang
Shin Jang
HKHyounjin Kim
Hyounjin Kim
Yeongjun KimYeongjun Kim
Yeongjun Kim
BKByung Ju Kang
Byung Ju Kang
JOJe Hoon Oh
Je Hoon Oh
In this study, a honeycomb-like nanofiber based triboelectric nanogenerator (HN-TENG) is presented. In order to fabricate the honeycomb-like nanofiber, we utilized self-assembly of electrospun poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)) nanofibers. The honeycomb-like P(VDF-TrFE) nanofiber network was directly produced via electrospinning without any additional processing. The HN-TENG showed a maximum voltage, current, and power density of 160 V, 17 μA, and 1.6 W/m2, respectively. The power density was enhanced more than twofold as compared with a typical flat nanofiber network based TENG due to the large surface area and high surface roughness of the honeycomb structure. Finally, we verified that HN-TENG has the potential to be used for practical applications by driving 100 light emitting diodes and charging capacitors.

1 July 2019 in Microelectronic Engineering
Verified
Journal Article
Closed access
Yeongjun KimYeongjun Kim
Yeongjun Kim
SJShin Jang
Shin Jang
JOJe Hoon Oh
Je Hoon Oh

14 August 2017 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
Yeongjun KimYeongjun Kim
Yeongjun Kim
SJShin Jang
Shin Jang
BKByung Ju Kang
Byung Ju Kang
JOJe Hoon Oh
Je Hoon Oh
Highly sensitive capacitive pressure sensors with poly(vinylidenefluoride-co-trifluoroethylene) (P(VDF-TrFE)) dielectric layers were prepared. The dielectric layers were directly produced by electrospinning P(VDF-TrFE) nanofibers for various spinning times. A longer spinning time enhanced the deformability of the electrospun P(VDF-TrFE) layers, resulting in higher sensitivity owing to larger changes in the deformation of the dielectric layer. One of the capacitive pressure sensors showed a high sensitivity of 2.81 kPa−1 at a pressure ≤ 0.12 kPa, a good response time of 42 ms, and small hysteresis. The sensitivity of the sensor was five times higher than that of a typical capacitive pressure sensor. The fabricated pressure sensor could detect a tiny water droplet as light as 7 mg. It is expected that the electrospun P(VDF-TrFE) nanofibers can be used as sensing materials for highly sensitive pressure sensors in wearable electronics applications.

5 January 2015 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
Yeongjun KimYeongjun Kim
Yeongjun Kim
SJShin Jang
Shin Jang
JOJe Hoon Oh
Je Hoon Oh
The effect of the needle shape on electrohydrodynamic (EHD) printing was investigated by comparing flat outlet needles and hypodermic needles. Line fabrication was performed to confirm the tendency of jetting stability and the printed line width with various driving voltage and stage speed by using Ag nanoparticle ink as a jetting solution on a hydrophobic surface. We verified that the hypodermic needle greatly improves the resolution in EHD printing. The ink slips down the inner wall of the hypodermic needle, and a very small meniscus is generated at the tip of the needle. Due to this phenomenon, high-resolution printing can be accomplished. The narrowest line that was fabricated using a hypodermic needle has a line width of 0.7 μm, and it is smaller than 1% of the needle inner diameter.

14 September 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Yeongjun KimYeongjun Kim
Yeongjun Kim
JOJe Hoon Oh
Je Hoon Oh
In recent years, innovative research has been widely conducted on flexible devices for wearable electronics applications. Many examples of wearable electronics, such as smartwatches and glasses, are already available to consumers. However, strictly speaking, the sensors used in these devices are not flexible. Many studies are underway to address a wider range of wearable electronics and the development of related fields is progressing very rapidly. In particular, there is intense interest in the research field of flexible pressure sensors because they can collect and use information regarding a wide variety of sources. Through the combination of novel materials and fabrication methods, human-machine interfaces, biomedical sensors, and motion detection techniques, it is now possible to produce sensors with a superior level of performance to meet the demands of wearable electronics. In addition, more compact and human-friendly sensors have been invented in recent years, as biodegradable and self-powered sensor systems have been studied. In this review, a comprehensive description of flexible pressure sensors will be covered, and design strategies that meet the needs for applications in wearable electronics will be presented. Moreover, we will cover several fabrication methods to implement these technologies and the corresponding real-world applications.