This paper presents a comprehensive power takeoff (PTO) analysis program conducted as a collaborative research effort between Columbia Power Technologies, Inc., Oregon State University (OSU), and the U.S. Navy. Eighteen different direct-drive technologies were evaluated analytically and down-selected to five promising designs. Each of the five prototypes was simulated, modeled in SolidWorks, and built at the 200-W peak level and tested on OSU's wave energy linear test bed. The simulations were validated with the 200-W experimental results and then scaled up to 100 kW, with full 100-kW designs including costs, maintenance, operations, etc., to estimate the cost of energy (COE) for each PTO buoy system at utility scale.
1 June 2015 in Journal of Atmospheric and Oceanic Technology
The effects of biofouling on a wave measurement buoy are examined using concurrent data collected with two Datawell Waveriders at Ocean Station P: one heavily biofouled at the end of a 26-month deployment, the other newly deployed and clean. The effects are limited to the high-frequency response of the buoy and are correctly diagnosed with the spectral “check factors” that compare horizontal and vertical displacements. A simple prediction for the progressive change in frequency response during biofouling reproduces the check factors over time. The bulk statistical parameters of significant wave height, peak period, average period, and peak direction are only slightly affected by the biofouling because the contaminated frequencies have very low energy throughout the comparison dataset.
3 November 2017 in IEEE Journal of Oceanic Engineering
Wave energy converters (WECs) often employ submerged heave plates to provide reaction forces at depths below the level of wave motion. Here, two sets of heave plate experiments are described, at varying scale. First, the Oscillator uses a linear actuator to force laboratory scale (30.5-cm diameter) heave plates in sinusoidal motion. Second, the miniWEC buoy uses vessel wakes to force field scale (1.5-m diameter) heave plates in open water with realistic energy conversion (damping). The motion and forces are analyzed using the Morison equation, in which the hydrodynamic coefficients of added mass $C_M$ and drag $C_D$ are determined for each set of Oscillator and miniWEC experiments. Results show strong intracycle variations in these coefficients, yet constant hydrodynamic coefficients provide a reasonable reconstruction of the time series data. The two test scales are examined relative to the Keulegan–Carpenter number ($\text{KC}$), Reynold’s number ($Re$), and Beta number ($\beta$). The effects of asymmetric shape on hydrodynamic performance are found to be small.
10 October 2018 in IEEE Journal of Oceanic Engineering
Surface wave instrumentation floats with tracking were deployed by helicopter ahead of five large storms off the Oregon coast. The buoys drifted freely with the wave motions, surface currents, and wind. The buoys use a 9-DoF inertial measurement unit that fuses the measurements of accelerometers, magnetometers, and gyroscopes to measure acceleration in the global North-West-Up reference frame. Rapid sampling (25 Hz) allows for the observation of both propagating wave motions and wave breaking events. Bulk wave parameters and wave spectra are calculated from the motion of the buoys using conventional methods, and breaking wave impacts are identified in the raw acceleration data using a new algorithm based on a short-time Fourier transform. The number of breaking waves is used to infer breaker fraction, which is found to depend on bulk wave steepness as previously shown in the literature. The magnitude and duration of acceleration during breaking is used in a new quantification of breaker intensity, which increases with wave height, period, and steepness. There is significant variance of breaker intensity in a given wave field, such that intense breakers still occur in relatively mild wave fields. The buoy observations are compared to the output of the WaveWatch III forecast model, with evaluation of an empirical breaker prediction scheme applied to WaveWatch III output.
A spherical wave measurement buoy capable of detecting breaking waves has been designed and built. The buoy is 16 inches in diameter and houses a 9 degree of freedom inertial measurement unit (IMU). The orientation and acceleration of the buoy is continuously logged at frequencies up to 200 Hz providing a high fidelity description of the motion of the buoy as it is impacted by breaking waves. The buoy was deployed several times throughout the winter of 2013–2014. Both moored and free-drifting data were acquired in near-shore shoaling waves off the coast of Newport, OR. Almost 200 breaking waves of varying type and intensity were measured over the course of multiple deployments. The characteristic signature of spilling and plunging breakers was identified in the IMU data.