Proton exchange membrane fuel cells (PEMFCs) employing proton conducting membranes are promising power sources for automotive applications. Perfluorosulfonic acid (PFSA) ionomer represents the state-of-the-art polymer used in both the membrane and catalyst layer to facilitate the transport of protons. However, PFSA ionomer is recognized as having significant drawbacks for large-scale commercialization, which include the high cost of synthesis and use of fluorine-based chemistry. According to published research much effort has been directed to the synthesis and study of non-PFSA electrolyte membranes, commonly referred to as hydrocarbon membranes, which has led to optimism that the less expensive proton conducting membranes will be available in the not-so-distant future. Equally important, however, is the replacement of PFSA ionomer in the catalyst layer, but in contrast to membranes, studies of catalyst layers that incorporate a hydrocarbon polyelectrolyte are relatively sparse and have not been reviewed in the open literature; despite the knowledge that hydrocarbon polyelectrolytes in the catalyst layer generally lead to a decrease in electrochemical fuel cell kinetics and mass transport. This review highlights the role of the solid polymer electrolyte in catalyst layers on pertinent parameters associated with fuel cell performance, and focuses on the effect of replacing perfluorosulfonic acid ionomer with hydrocarbon polyelectrolytes. Collectively, this review aims to provide a better understanding of factors that have hindered the transition from PFSA to non-PFSA based catalyst layers.
The low-temperature electrolysis of CO2 in membrane-based flow reactors is a promising technology for converting captured CO2 into valuable chemicals and fuels. In recent years, substantial improvements in reactor design have significantly improved the economic viability of this technology; thus, the field has experienced a rapid increase in research interest. Among the factors related to reactor design, the ion exchange membrane (IEM) plays a prominent role in the energetic efficiency of CO2 conversion into useful products. Reactors utilizing cation exchange, anion exchange and bipolar membranes have all been developed, each providing unique benefits and challenges that must be overcome before large-scale commercialization is feasible. Therefore, to direct advances in IEM technology specific to electrochemical CO2 reduction reactions (CO2RRs), this review serves to first provide polymer scientists with a general understanding of membrane-based CO2RR reactors and membrane-related shortcomings and to encourage systematic synthetic approaches to develop membranes that meet the specific requirements of CO2RRs. Second, this review provides researchers in the fields of electrocatalysis and CO2RRs with more detailed insight into the often-overlooked membrane roles and requirements; thus, new methodologies for membrane evaluation during CO2RR may be developed. By using CO2-to-CO/HCOO− methodologies as practical baseline systems, a clear conceptualization of the merits and challenges of different systems and reasonable objectives for future research and development are presented. Graphical Abstract
15 November 2021 in The Journal of Physical Chemistry C
The dependence of performance and stability of a zero‐gap CO2 electrolyzer on the properties of the anion exchange membrane (AEM) is examined. This work firstly assesses the influence of the anolyte when using an Aemion membrane and then shows that when using 10 mM KHCO3, a CO2 electrolyzer using a next‐generation Aemion+ membrane can achieve lower cell voltages and longer lifetimes due to increased water permeation. The impact of lower permselectivity of Aemion+ on water transport is also discussed. Using Aemion+, a cell voltage of 3.17 V at 200 mA cm−2 is achieved at room temperature, with a faradaic efficiency of >90 %. Stable CO2 electrolysis at 100 mA cm−2 is demonstrated for 100 h, but with reduced lifetime at 300 mA cm−2. However, the lifetime of the cell at high current densities is shown to be increased by improving water transport characteristics of the AEM and reducing dimensional swelling, as well as by improving cathode design to reduce localized dehydration of the membrane.
Optimization of the ionomer materials in catalyst layers (CLs) which sometimes is overlooked has been equally crucial as selection of the membranes in membrane electrode assembly (MEA) for achieving a superior performance in proton exchange membrane fuel cells (PEMFCs). Four combinations of the MEAs composed of short-side-chain (SSC) and long-side-chain (LSC) perfluorosulfonic acid (PFSA) polymers as membrane and ionomer materials have been prepared and tested under various temperatures and humidity conditions, aiming to investigate the effects of different side chain polymer in membranes and CLs on fuel cell performance. It is discovered that SSC PFSA polymer used as membrane and ionomer in CL yields better fuel cell performance than LSC PFSA polymer, especially at high temperature and low RH conditions. The MEA with the SSC PFSA employed both as a membrane and as an ionomer in cathode CL demonstrates the best cell performance amongst the investigated MEAs. Furthermore, various electrochemical diagnoses have been applied to fundamentally understand the contributions of the different resistances to the overall cell performance. It is illustrated that the charge transfer resistance (Rct) made the greatest contribution to the overall cell resistance and then membrane resistance (Rm), implying that the use of the advanced ionomer in CL could lead to more noticeable improvement in cell performance than only the substitution as the membrane.