Stefan Meyer

Mr. Stefan Meyer

TUM
+1
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2018 in Polymer Engineering & Science
Verified
Journal Article
Closed access
PDF file
CSChristian Schäfer
Christian Schäfer
SMStefan Meyer
Stefan Meyer
TOTim A. Osswald
Tim A. Osswald

14 February 2019 in Production Engineering
Verified
Journal Article
Open access
PDF file
FLFlorian P. Lugauer
Florian P. Lugauer
AKAndreas Kandler
Andreas Kandler
SMStefan Meyer
Stefan Meyer
CWChristoph Wunderling
Christoph Wunderling
MZMichael F. Zaeh
Michael F. Zaeh
The importance of hybrid composites is increasing, particularly with regard to structural lightweight construction. Therefore, a joining process for the production of hybrid bonds using induction technology is examined in this paper. An appropriate test rig was developed, assembled, commissioned and characterized for this purpose. Heating tests with titanium Ti6Al4V were carried out with this device to determine the influence of the process parameters on the temperature level and the temperature field. This applies in particular to the feed rate, the sample geometry, the relative positioning between sample and inductor as well as to the inductor setting like induction frequency and pulse width modulation. Based on the results of these examinations, a two-stage heating process was developed, which allows the formation of a homogeneous temperature field in the range of the melting and degradation temperature of the used polymer (PPS; Ten-Cate Cetex TC1100) and thus to achieve optimized bond strengths. More specifically, a short phase with a high energy input was used for quick and intensive warming and a longer time period was deployed to reach an even distribution of temperature. Subsequently, joints with CFRP were produced with a specimen geometry suitable for tensile shear tests according to DIN EN 1465 (Adhesives—determination of tensile lap-shear strength of bonded assemblies; German version EN 1465:2009, 2009). The analysis of the tensile shear strength and the fractured surfaces shows that the metal is much more difficult to heat up due to the melting enthalpy of the plastic than preliminary tests indicated. Further tests were carried out, which revealed a threshold value for heating where the temperature was sufficiently high to achieve a complete coating of the plastic on the metal can be achieved. In summary, the investigations showed that the presented method as well as the design of the test rig is generally suitable for bonding metal to thermoplastic polymers. The influence of various parameters on heating and bond strength could be identified. Moreover a process has been established, which allows industrially useful bonding forces. This not only proves that further investigations are useful, but also laid the foundation for further experiments.

5 March 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
SMStefan Meyer
Stefan Meyer
BJB Jaeger
B Jaeger
CWC Wunderling
C Wunderling
MZM F Zaeh
M F Zaeh

3 November 2019 in Production Engineering
Verified
Journal Article
Open access
PDF file
SMStefan Meyer
Stefan Meyer
CWChristoph Wunderling
Christoph Wunderling
MZMichael F. Zaeh
Michael F. Zaeh
Friction press joining is an innovative joining process for the production of plastic-metal joints without additives, in an overlap configuration. In order to achieve a high bond strength, the metallic joining partner is pretreated with laser radiation. Subsequently, heat is induced by friction and pressure during the joining process, causing the thermoplastic material to melt and adhere to the metallic joining partner. In this work, the temperature distribution during the process in the composite is analyzed and characterized. It was found that the occurring temperatures and temperature differences are not only dependent on the rotational speed, but also on the feed rate. It is also shown that the friction surface temperature can be used as an indirect control variable for a model-based, closed-loop control. Based on these findings, various surface modifications for the metallic joining partner were investigated and analyzed with regard to the maximum strength of the joint. It was observed that the highest tensile shear strength can be achieved with a quasi-chaotic nano structure. In addition, the joining compound was characterized by a thin section, facilitating the identification of specific zones in the joint. These investigations show the high potential for friction press joining of plastics and metals, and form the basis for a model-based control of the joining zone temperature.

1 August 2020 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
CWC. Wunderling
C. Wunderling
LML. Mayr
L. Mayr
SMStefan Meyer
Stefan Meyer
MZM.F. Zaeh
M.F. Zaeh

30 June 2020 in Production Engineering
Verified
Journal Article
Open access
PDF file
SMStefan Meyer
Stefan Meyer
CBChristian Bernauer
Christian Bernauer
SGSophie Grabmann
Sophie Grabmann
MZMichael F. Zaeh
Michael F. Zaeh
Friction press joining is an innovative joining process for bonding plastics and metals without additives in an overlap configuration. A model-based approach for the design of an axial force controller for friction press joining is presented in this paper. A closed-loop control was set up on the machining center, in which the plunge depth was used as the controlling variable. In order to support the controller development, a nonparametric dynamic process model was developed via a data-based system identification. Subsequently, various control concepts were designed off-line and verified on the actual system. The most promising ones, a proportional controller, a controller created with the pole placement method, and a model predictive controller, were selected for further investigations. The three controllers were re-evaluated and compared by means of a defined input of disturbance variables and reference variables. The model predictive control (MPC) approach as well as the proportional controller were also tested for model uncertainties. For this purpose, different material combinations were joined using the different controllers. Thereby, it was shown that the MPC controller resulted in smaller standard deviations when encountering large model uncertainties. The investigations demonstrated the high potential of friction press joining of plastic components with metals. The results form the basis for future research, whereby the force can be specified as an additional input parameter instead of the plunge depth.