jinhong tan

Dr. jinhong tan

Guangdong Welding Institute (China-Ukraine E.O. Paton Institute of Welding)

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 February 2020 in Metals
Verified
Journal Article
Open access
PDF file
SMShu Miao
Shu Miao
ZXZhuoming Xie
Zhuoming Xie
YLYan Lin
Yan Lin
QFQianfeng Fang
Qianfeng Fang
JTjinhong tan
jinhong tan
YZyunqiang zhao
yunqiang zhao
Tungsten materials, used as friction stir welding tools, undergo severe plastic deformation and even collapse at high operating temperatures. In order to improve the low-temperature toughness and high-temperature strength, W-10wt.%Re-0.5wt.%ZrC alloys were processed by high-energy ball milling and subsequent spark plasma sintering. Single solid-solution W-Re powders with typical body-centered cubic structures were achieved when the milling time increases to 50 h. The microhardness, tensile properties, thermal stability and microstructures of this sintered W-10wt.%Re-0.5wt.%ZrC alloys were investigated. Synergetic effects of the solute Re and nanosized dispersion particles induce improvements in low-temperature toughness and high-temperature strength. The alloy suffers ductile fracture at 300 °C, which is about 400 °C and 300 °C lower than that of the spark plasma sintered pure W and W-0.5wt.%ZrC, respectively. Besides, this W-10wt.%Re-0.5wt.%ZrC has a high ultimate tensile strength of 818 MPa and uniform elongation of ~ 8.1% at 300 °C. Moreover, the microstructures and hardness remain stable even after 1500 °C anneal. Based on a detailed microstructure analysis, the mechanisms for the enhanced strength, low-temperature ductility and high thermal stability are proposed and discussed. Grain boundary mobility is impeded by the kinetics constraint through dispersed particles pinning and solute Re atoms dragging, which leads to improved thermal stability. The formation of Zr-C-O particles is most probably attributed to ZrC particles capturing and interacting with impurity oxygen during sintering.

17 January 2020 in Metals
Verified
Journal Article
Open access
PDF file
YZyunqiang zhao
yunqiang zhao
CDChunlin Dong
Chunlin Dong
CWchungui wang
chungui wang
SMShu Miao
Shu Miao
JTjinhong tan
jinhong tan
YYYaoyong Yi
Yaoyong Yi
In this study, Al-Zn-Mg-Cu alloy was refill friction spot welded, and the precipitates, dislocation, recovery, and recrystallization characteristics were focused. In the stir zone (SZ), continues dynamic recrystallization occurs under the intense plastic deformation. All the original GP (II) zones and η’ precipitates dissolved into the aluminum matrix under the welding heat input, and the stable η and E precipitates remained. In the thermo-mechanically affected zone (TMAZ), high-density dislocations and subgrains boundaries can be observed. The continued dynamic recrystallization was not activated and only dynamic recovery occurs. Sub-boundaries and high-density dislocations in this zone can be observed. In this zone, the η precipitates are coarsened and dissolution is the main evolution mechanism for the GP (II) zones and η’ precipitates. In the heat-affected zone (HAZ), no dislocation was induced and all the initial precipitates were coarsened under the welding heat input. The HAZ, the TMAZ, and the SZ constitute a soft region in the refill friction stir spot welding (RFSSW) joint, and the minimum value located at the interface between the HAZ and the TMAZ.

1 January 2021 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
YZyunqiang zhao
yunqiang zhao
CDChunlin Dong
Chunlin Dong
ZJZhongxue Jia
Zhongxue Jia
JYJiaqing You
Jiaqing You
JTjinhong tan
jinhong tan
YYYaoyong Yi
Yaoyong Yi
In this study, 2205 duplex stainless steel was friction‐stir‐welded at different welding speeds. The microstructural characteristics such as grain sizes, grain boundary misorientation angles, and phase contents in the stir zones of the joints were detected. The potentiodynamic polarization and electrochemical impedance spectroscopy were also measured to evaluate the corrosion property of the stir zones. The effects of the microstructures on the corrosion property for friction‐stir‐welded 2205 duplex stainless steel were analyzed. The results indicated that the FSW process refined the grains and increased the ferrite contents in the stir zones. With increasing the welding speed from 30 mm/min to 50 mm/min, the grain size in the stir zone decreased from 1.64 μm to 0.96 μm, the ferrite content decreased from 59% to 54.4%, and the fractions of low angle grain boundaries for austenite and ferrite phases decreased from 63.9% and 92.6% to 18.0% and 41.1%, respectively. In this study, the effect of grain size on the corrosion resistance was the most significant and it was followed by the phase composition and the grain boundary misorientation angle. The stir zone obtained at 50 mm/min has the highest corrosion resistance, and it is followed by the base material and the stir zone obtained at 30 mm/min.