In the present review, natural and non-toxic particles made of micro/nanocellulose were specifically targeted as stabilizers of emulsions located at dispersed and continuous phases interfaces (called Pickering Emulsions, PEs). PEs are biphasic systems stabilized by solid particles with a recent interest in food and cosmetic domains. PEs have been more and more studied in the last ten years due to their advantages compared to conventional emulsions with surfactants. PEs have already been stabilized with various types of particles and particularly cellulose. Even if some studies showed that PEs were more stable when cellulose was chemically modified, numerous other recent studies showed that unmodified micro/nanocellulose is also promising biomaterial to stabilize PEs. Micro/nanocelluloses can be extracted by various green processes from numerous agricultural wastes and co-products, as banana peels, corncob, ginkgo seed shells, lime residues, mangosteen rind, oil palm empty fruit bunches, pistachio shells, as well as wheat straw. Main green processes used to treat cellulose are grinding, high pressure homogenization, microfluidization, enzymatic hydrolysis, subcritical water, extrusion, electron beam irradiation, cryocrushing, microwaves or sonication. PEs formulated with cellulose clearly participate to a global sustainable development but, additional studies will be necessary to better understand PEs stability and improve properties.

Emulsions are multiphasic systems composed of at least two immiscible phases. Emulsion formulation can be made by numerous processes such as low-frequency ultrasounds, high-pressure homogenization, microfluidization, as well as membrane emulsification. These processes often need emulsifiers’ presence to help formulate emulsions and to stabilize them over time. However, certain emulsifiers, especially chemical stabilizers, are less and less desired in products because of their negative environment and health impacts. Thus, to avoid them, promising processes using high-frequency ultrasounds were developed to formulate and stabilize emulsifier-free emulsions. High-frequency ultrasounds are ultrasounds having frequency greater than 100 kHz. Until now, emulsifier-free emulsions’ stability is not fully understood. Some authors suppose that stability is obtained through hydroxide ions’ organization at the hydrophobic/water interfaces, which have been mainly demonstrated by macroscopic studies. Whereas other authors, using microscopic studies, or simulation studies, suppose that the hydrophobic/water interfaces would be rather stabilized thanks to hydronium ions. These theories are discussed in this review.

Cellulose is a promising renewable and biocompatible biopolymer for stabilizing Pickering emulsions (PEs). In the present study, PEs were produced by low-frequency ultrasounds with cellulose nanocrystals (CNCs) and caprylic/capric triglycerides. Phase diagrams allowed to understand mechanisms of formation and long-term stabilization of PEs. Emulsion type, continuous phase viscosity, and yield of oil incorporation were studied after PEs formation. Droplet size, oil release, and stability were measured weekly up to 56 days of storage. Results showed that oil mass fraction above 70% w/w led to unstable W/O PEs. Lower oil mass fraction formed O/W PEs of stability depending on CNC content and oil mass fraction. Droplet size stability increased with CNCs/oil ratio. A very low CNCs/oil ratio led to phase separation and oil release. High CNC content stabilized oil droplets surface, increased aqueous phase viscosity, and prevented creaming. Highly stable PEs were produced for CNC content above 3% (w/w) and oil mass fraction below 50% (w/w). Mechanisms for PEs formation and stabilization were proposed for various CNC contents and oil mass fractions.

The use of bioresourced packaging materials is an interesting solution for ecological issues. This work aimed to develop novel chitosan-based packaging materials reinforced with hemp fibers (HF). For this purpose, chitosan (CH) films were filled with 15%, 30%, and 50% (w/w) of two kinds of HF: Untreated fibers cut to 1 mm (UHF) and steam exploded fibers (SEHF). The effect of HF addition and HF treatments on chitosan composites was studied in terms of mechanical properties (tensile strength (TS), elongation at break (EB), and Young’s modulus (YM)), barrier properties (water vapor (WVP) and oxygen permeabilities), and thermal properties (glass transition (T_g) and melting temperatures (T_m)). The addition of HF, whether untreated or steam exploded, increased the TS of chitosan composites by 34–65%. WVP was significantly reduced by the addition of HF but no significant change was observed for O₂ barrier property, which was in the range between 0.44 and 0.68 cm³·mm/m²·d. T_m of the composite films increased from 133 °C for CH films to 171 °C for films filled with 15% SEHF. However, no significant modification was observed for T_g (105–107 °C). The present study showed that the developed biocomposites had improved properties, mainly the mechanical resistance. Their use in food packaging will help industrials the move toward a sustainable development and circular economy.

Cellulose, in the form of cellulose nanocrystals (CNCs), is a promising biomaterial for stabilizing Pickering emulsions (PEs). PEs are commonly formed using low-frequency ultrasound (LFU) treatment and impact CNC properties. The present study investigated the specific effects of LFU treatment on CNCs’ chemical and physical properties. CNCs were characterized using dynamic light scattering, ζ;-potential determination, Fourier transform infrared spectroscopy, X-ray diffraction, and contact angle measurement. CNC suspensions were studied using rheological analysis and static multiple light scattering. LFU treatment broke CNC aggregates and modified the rheological behavior of CNC suspensions but did not affect the CNCs’ chemical or crystallographic structures, surface charge, or hydrophilic properties. During the storage of CNC suspensions and PEs, liquid crystal formation was observed with cross-polarized light. Hypotheses related to the impact of liquid crystal CNCs on PE stability were proposed.