Polyaniline (PANI) was synthesized chemically with the modified rapid mixing protocol in the presence of sulfuric acid of various concentrations. A two-step synthetic procedure was utilized maintaining low-temperature conditions. Application of the modified rapid mixing protocol allowed obtaining a material with local ordering. A higher concentration of acid allowed obtaining a higher yield of the reaction. Structural characterization performed with Fourier-transform infrared (FTIR) analysis showed the vibration bands characteristic of the formation of the emeraldine salt in both products. Ultraviolet–visible light (UV–Vis) spectroscopy was used for the polaronic band and the p–p* band determination. The absorption result served to estimate the average oxidation level of PANI by comparison of the ratio of the absorbance of the polaronic band to that of the π–π* transition. The absorbance ratio index was higher for PANI synthesized in a more acidic solution, which showed a higher doping level for this polymer. For final powder products, particle size distributions were also estimated, proving that PANI (5.0 M) is characterized by a larger number of small particles; however, these particles can more easily agglomerate and form larger structures. The X-ray diffraction (XRD) patterns revealed an equilibrium between the amorphous and semicrystalline phase in the doped PANI. A higher electrical conductivity value was measured for polymer synthesized in a higher acid concentration. The time-of-flight secondary ion mass spectrometry (TOF-SIMS) analysis showed that the molecular composition of the polymers was the same; hence, the difference in properties was a result of local ordering.
Various alkali metal salts were applied as initiators for ε-caprolactone anionic ring-opening polymerization in tetrahydrofuran at room temperature. It was observed that potassium methoxide (MeOK), potassium isopropoxide (i-PrOK) and potassium tert-butoxide (t-BuOK) nonactivated or activated by 18-crown-6 (18C6) initiated polymerization mainly by deprotonation of the monomer. In the case of potassium hydride (KH), its basicity increased with the ability of the ligand for cation complexation. For example, KH without ligand or with weak ligands for K+ as 12C4 reacted exclusively by ring opening. However, in the presence of strong ligands, as 15C5, 18C6 or cryptand C222, basicity of H− increased with the ability of the ligand for cation complexation. In the last case, ~ 32% of the monomer was deprotonated. In these systems, gaseous H2 evolved during the initiation. Deprotonation of the monomer by some initiators resulted in macromolecules with reactive aldehyde group or lactone ring as starting groups. They took part in the reaction with potassium alkoxide active centers of growing chains leading to the formation of branched poly(ε-caprolactone)s. Sodium hydride (NaH) was inactive, but in the presence of 15-crown-5 or 18-crown-6 initiated polymerization exclusively by ring opening. MALDI-TOF mass spectrometry supported with 13C NMR and SEC was used for analysis of the polymers obtained. Mechanism of the studied processes was proposed and discussed.
In the present study, the structure and porosity of binary Ti–35Zr (wt.%) alloy were investigated, allowing to consider powder metallurgy as a production method for new metallic materials for potential medical applications. The porous Ti–Zr alloys were obtained by milling, cold isostatic pressing and sintering. The pressure during cold isostatic pressing was a changing parameter and was respectively 250, 500, 750 and 1000 MPa. The X-ray diffraction study revealed only the α phase, which corresponds to the Ti–Zr phase diagram. The microstructure of the Ti–35Zr was observed by optical microscopy and scanning electron microscopy. These observations revealed that the volume fraction of the pores decreased from over 20% to about 7% with increasing pressure during the cold isostatic pressing. The microhardness measurements showed changes from 137 HV0.5 to 225 HV0.5.
Anionic polymerization of propylene oxide was carried out in the presence of two groups of potassium salts activated 18-crown-6 (18C6), e.g. alkoxide salts (CH3OK, i-PrOK, t-BuOK, CH3OCH2CH(CH3)OK, KCH2O) and other salts (CbK, Ph3CK, Ph2PK, Ph3HBK, KK, KH, and [(CH3)3Si]2NK) in THF at room temperature. Application of various initiating systems results in polyethers which are different in level and kind of unsaturation represented by allyloxy, cis- and trans-propenyloxy, as well as vinyloxy starting groups. In the presence of selected initiator, i.e. t-BuO−K+ unsaturation increases markedly by addition of 18C6 or C222. During the initiation step oxirane ring-opening and direct deprotonation of the monomer occur simultaneously involving in some cases also the ligand. All initiators opens oxirane ring in the β-position except i-PrOK, which opens it in the β- and α-position. The mechanisms of the reactions were discussed.
Polypyrrole, which belongs to the conducting polymer family, has demonstrated profound potential in advanced water purification applications due to its inherent electrical conductivity, environmental stability, and tunable surface chemistry. As a sorbent, PPy exhibits high sorption capacity for aquatic contaminants, including heavy metals, pharmaceutical compounds, and their metabolites, as well as synthetic dyes. The removal efficiency is correlated to a complex interaction mechanism involving electrostatic attractions, redox activity, and π–π stacking. Recent advances have expanded the utility by further developing nanostructured PPy-based (nano)composites, which elevate sorption performance by increasing surface area, mechanical integrity, and selective affinity. In addition, its integration into membrane technologies has enabled the design of an effective filtration system with improved selectivity and regeneration capabilities. Moreover, PPy is effective in electrochemical processes of water treatment, including capacitive deionization and electrochemically assisted sorption, opening novel paths towards energy-efficient pollutant removal. The multifunctionality of PPy as a sorbent material highlights its value as an important material for water treatment, with the capability of extended modification tailored for emerging environmental needs revised in this work.
Several alkali metal salts that activated 18-crown-6 were applied as initiators of β-butyrolactone anionic ring-opening polymerization in tetrahydrofuran at room temperature. Some of them, i.e., Ph2PK, Ph3HBK, (Me3Si)2NK, and t-BuOK, deprotonate the monomer which results in macromolecules with trans-crotonate starting group. Other salts, for example, MeOK, i-PrOK, PhCH2OK, and CbK (Cb denotes carbazolyl group), deprotonate monomer or open its ring in the acyl-oxygen position. After ring-opening KOH forms as intermediate and initiates further polymerization. Ph3CK and monopotassium salt of ethylenediaminetetraacetic acid also deprotonate monomer and open its ring, however, in the alkyl-oxygen position. Monopotassium salts of glycolic acid, diglycolic acid, or malonic acid initiate polymerization mainly by ring opening in the alkyl-oxygen position. It results in the formation of polymers with two reactive terminal groups. The salts used react with the monomer as strong bases, nucleophilic bases, or nucleophiles. It determines unsaturation of the polymers obtained in the wide range of 2–100 mol%.