This letter presents a hybrid series-shunt LC tank matching technique, which constructs an imaginary-impedance part for impendence (power) matching and cancels the imaginary-impedance deviations caused by the aggravated load and parasitic effects in millimeter-wave (mm-wave) high-frequency band, allowing broadband simultaneous noise and impedance matching (BSNIM) for mm-wave CMOS low-noise amplifier (LNA). The proposed matching network has been synthesized into a triple-coupled transformer-based matching network further to enable a compact and robust solution in differential circuit design. To validate the proposed BSNIM techniques, an $E$ / $W$ -band LNA is fabricated with 40-nm CMOS, and achieves less than $-$ 10 dB S11 from 58 to 110 GHz and a low noise figure (NF) of 4.2–6.9 dB from 58 to 100 GHz. The peak gain of the LNA is 16.4 dB at 85 GHz with a 3-dB gain bandwidth (BW) from 70 to 91 GHz, while consuming 20.7 mW from 0.9-V supply.
5 May 2022 in IEEE Microwave and Wireless Components Letters
This letter presents a convenient approach based on the two-port kQ-product theory to analyze the influence of interwinding capacitive coupling on the efficiency of the transformer. It is demonstrated that a transformer with proper size can benefit from the interwinding capacitive coupling to maximize its efficiency at a desired frequency. The proposed design approach is used in a W-band low-noise amplifier (LNA) fabricated with the 40-nm CMOS process to optimize the insertion loss of the input transformer-based balun. Thanks to the approach, the W-band LNA achieves a minimum noise figure of 5.7 dB, a maximum gain of 18.5 dB, and a 3-dB bandwidth of 76.5-92.6 GHz, while consuming 23.4 mW from a 0.9-V supply.
9 August 2018 in IEEE Transactions on Microwave Theory and Techniques
We present a fully-integrated 256 QAM single-chip transceiver (TRX) with 300-MHz channel bandwidth at the 6.5-GHz band. A novel architecture for self-interference suppression (SIS) is proposed. A noise-canceling low-noise amplifier with the embedded programmable source degeneration network based on the bond wires, manifesting the notch filtering characteristics of the self-interference signal, has been utilized to facilitate the SIS, and LC-tuned tanks further improve the interference filtering in a receiver (RX) and considerable adjacent channel leakage power ratio in a transmitter (TX). The SAW-less/duplexer-less TRX allows TDD/FDD co-operation in closely spaced channels. The RX achieves a noise figure (NF) as low as 3 dB with +17.5-dBm out-of-band IIP3. The EVM is 2.02% and 2.72% for the RX and TX, respectively, in 160-MHz bandwidth OFDM 256 QAM. In the SIS mode, the blocker P1dB is -8 dBm, and the NF of the RX degrades only 2.1 dB (from 3.0 to 5.1 dB), withstanding 0-dBm interference at 150-MHz offset. The TRX exhibits a slight EVM degradation (from 2.02% to 2.98%) when receiving a -40-dBm 160-MHz bandwidth 256 QAM desired signal, in the presence of a -15-dBm 80-MHz bandwidth self-interference signal at 300-MHz offset. The TRX has been implemented in 0.13-μm CMOS with superior overall performances.
22 July 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a high accuracy high linearity K-Band 4-channel phased array receiver for satellite communication (SATCOM). Structural improvement and parameter optimization have been carried out to enhance the phase and gain control precision. The presented receiver employs a novel L-C compensation and variable resistance technique in the quadrature all-pass filter (QAF) for phase shifter (PS) to reduce the phase error. Neutralization capacitance and redundancy control bit are adopted in the attenuator (ATT) to reduce the gain error. A 3-stage low noise amplifier (LNA) has been optimized to provide high gain, high input-referred 1-dB gain compression point and low noise. The receiver achieves a 360° phase shifting range with a 6-bit resolution and a 31.5 dB attenuation range with 0.5 dB step. The measured root mean square (RMS) phase error and gain error are 0.78°–1.22° and 0.14–0.32 dB, respectively over the frequency of 17 GHz to 23 GHz. Each channel achieves a measured gain of 23 dB, an input-referred 1-dB gain compression point (IP1dB) of –29.8 dBm at the maximum gain, and a low noise figure (NF) of 3.4–3.9 dB. The 4-channel receiver is implemented in 40-nm CMOS processes and occupies a chip area of 3.85 mm2.
This paper presents a Ku-band fractional-N frequency synthesizer with adaptive loop bandwidth control (ALBC) to speed up the lock settling process and meanwhile ensure better phase noise and spur performance. The theoretical analysis and circuits implementation are discussed in detail. Other key modules of the frequency synthesizer such as broadband voltage-controlled oscillator (VCO) with auto frequency calibration (AFC) and programable frequency divider/charge pump/loop filter are designed for integrity and flexible configuration. The proposed frequency synthesizer is fabricated in 0.13 m CMOS technology occupying 1.14 × 1.18 mm area including ESD/IOs and pads, and the area of the ALBC is only 55 × 76 m. The out frequency can cover from 11.37 GHz to 14.8 GHz with a frequency tuning range (FTR) of 26.2%. The phase noise is −112.5 dBc/Hz @ 1 MHz and −122.4 dBc/Hz @ 3 MHz at 13 GHz carrier frequency. Thanks to the proposed ALBC, the lock-time can be shortened by about 30% from about 36 s to 24 s. The chip area and power consumption of the proposed ALBC technology are slight, but the beneficial effect is significant.
25 July 2024 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a technique of frequency-dependent implicit capacitance neutralization (FD-ICN) among capacitor bank and varactors in $LC$ voltage-controlled oscillator (VCO) to facilitate ultralow VCO gain ( $K_{\text{VCO}}$ ) across an octave frequency tuning range (TR). Series interconnect inductors are used between capacitor units to feature the inverse capacitance–frequency ( $C$ – $f$ ) relationship with varactors, thus yielding the proposed FD-ICN. A split 8-bit capacitor bank with centrosymmetric double-cross layout pattern is designed, enabling an enhanced FD-ICN through multiple capacitance equivalent iterations of the capacitor bank. The proposed FD-ICN technique is validated in a prototype of dual-mode electric-coupling VCO and fabricated in 130-nm CMOS process, exhibiting a measured frequency TR of 72.1% from 6.49 to 13.81 GHz with a $K_{\text{VCO}}$ of 7–73 MHz/V. The VCO shows a competitive phase noise (PN) and figures-of-merit in TR (FoM $\rm{_T}$ ) from $-$ 121.3 to $-$ 111.4 dBc/Hz and 197.4 to 201.7 dBc/Hz at 1-MHz offset across the whole TR.