This study constructs a prediction model of thermal deformation with an artificial neural network and implements the real-time error compensation for a three-axis vertical CNC milling machine in cutting processes to improve the thermal error of the workpiece. There are 32 PT-100 thermal sensors installed in key parts of the machine in order to measure the temperature of key machine parts in actual cutting conditions. Pearson’s correlation coefficients are used to select crucial temperature sensors for building the prediction model of thermal deformation. The reduced number of crucial temperature sensors in model construction can simplify the model complexity and speed up the response time of prediction. This study constructs a long short-term memory (LSTM) neural network model to predict the thermal error of the machine in cutting processes. This prediction model of thermal deformation can be further used in real-time error compensation of the workpiece in cutting processes. In an 8 h cutting experiment, the dimensions of the workpiece show that, with real-time error compensation, the thermal error in X-axis decreases from 7 µm to 3 µm, the thermal error in Y-axis decreases from 74 µm to 21 µm, and the thermal error in Z-axis decreases from −64 µm to −20 µm. The results indicate that the prediction model of thermal deformation and the real-time error compensation can significantly reduce the thermal error and improve the dimensional accuracy of the workpiece.
There is an increasing demand for large-sized hydrostatic rotary tables due to the industrial need for the precision machining of large workpieces for wind generation, aerospace, shipbuilding, and national defense applications. As a consequence, under eccentric loads, the deformation of the large-sized hydrostatic rotary table of a horizontal boring machine would negatively affect machining precision. Indeed, the hydrostatic thrust-bearing recess layout design is the main factor that affects the rotary table’s resistance against deformations caused by eccentric loads. This study focused on the capillary-compensated constant-pressure large-sized hydrostatic rotary table for a horizontal boring machine. ANSYS software was used to simulate the thermal and structural deformation of the worktable under eccentric loads. In addition to the original layout of the hydrostatic thrust bearing, three other bearing recess layouts, which involved two different recess diameters, were designed in order to examine the deformation of the worktable under eccentric loads. The results showed that, in terms of a single-ring hydrostatic thrust-bearing layout, a larger recess diameter resulted in a smaller worktable deformation compared to a smaller recess diameter; in terms of a dual-ring hydrostatic thrust bearing layout, the worktable deformation was smaller than that of the single-ring layout with a larger recess diameter. Under the spatial and geometric constraints of the worktable, adopting a hydrostatic thrust bearing with a dual-ring recess layout would minimize the worktable deformation under eccentric loads. For thermal deformation in a single-ring hydrostatic bearing pad layout, however, a larger recess diameter resulted in a larger worktable thermal deformation compared to a smaller recess diameter.
This study attempted to establish an optimal design and perform dynamic analysis for a spring-actuated cam-linkage composite mechanism in a rated 12 kV, 25 kA vacuum circuit breaker (VCB). The optimal design of the VCB mechanism involves two steps: the first step involves the optimal design of the stiffness of closing springs and the cam profile, based on three-order polynomial motion curve of the follower; the second step involves the optimal design of a four-bar linkage. To minimize the surplus work in the VCB operating mechanism, the overall difference between the general output force and general resistant force of the VCB operating mechanism during the closing operation was adopted as the objective function to be minimized. Furthermore, the differential evolution algorithm with the golden ratio (DE-gr), an efficient and accuracy metaheuristic algorithm, was employed as the optimization method. The dynamic analysis of the optimal operating mechanism was conducted using a MATLAB-coded program and verified by the multibody dynamic software MSC-ADAMS. The dynamic analysis revealed that the optimal design of the VCB mechanism can considerably decrease the average closing velocity of the movable contact and the Hertz stress between the contact surface of the cam and the roller follower.
This paper presents the world’s smallest inset permanent magnet synchronous motor (PMSM) with a soft magnetic composite (SMC) core, providing ease of manufacturing for micromachine applications without silicon steel laminations. The inset motor can offer an additional reluctance torque and higher torque density with a lower usage amount of permanent magnet. A 15 mm diameter inset motor was developed with the thickness of a tile-type permanent magnet which is limited to 1 mm by the manufacturer. The motor was designed with high torque density and low torque ripple by varying the interpole iron width for the rotor. Two inset motors were made using both SMC and silicon steel materials for comparison. The performance of the SMC motor was inferior to the silicon steel motor, but it still meets the specifications of the commercial market. If the thickness of the tile-type permanent magnet is further reduced, the micro inset motor with a SMC core can be easily mass-manufactured using powder sintering.
This study describes the development of the world’s smallest interior permanent magnet synchronous motor (IPMSM) to increase the torque density of micromotors. The research evaluates the feasibility of the miniaturization of IPMSM since recent studies in this area focus on medium to large size compressor and traction motor applications. The standard-type and spoke-type IPMSM were selected for ease of micro machining. In order to surpass the performance of an inset motor of the same size used in previous research, the interior motors were designed with a different slot pole number, permanent magnet shape and rotor structure. Two types of interior motors were manufactured and tested to compare their performance. It was shown that the spoke-type interior motor had a better output torque, while the standard-type interior motor had a lower torque ripple, and both motors matched the specifications of commercially available motors. To achieve a higher torque density, the IPMSM designs increased the slot pole number from 6 slots 4 poles to 9 slots 6 poles. The torque density of the spoke-type motor was increased by 48% compared to the inset motor. The disadvantage is that the new design has a greater number of parts and smaller size, resulting in difficulties in manufacturing and assembly.
This paper investigates the thermal characteristics of a vertical guideway system for precision milling machine applications by considering three heat sources, namely motor heat, viscous shearing heat of hydrostatic bearings, and friction heat from a ballscrew nut. A finite element (FE) model using ANSYS/Fluent was used to simulate the thermal characteristics of the system by considering the oil film friction of the hydrostatic bearings in the operational feed speed and heat generation in the ballscrew nut. Eight K-type thermocouples were installed in the vertical hydrostatic guideway system to measure the temperature rise in the key components. Nine thermal experiments of the vertical hydrostatic guideway system under three operational feed rates, namely 1.25, 2.5 and 5 m/min were conducted to measure the temperature of seven thermocouples in practical running conditions. The experimental temperature data then was used to adjust the FE model setting to guarantee the accurate prediction of the thermal deformation in real operational conditions. The FE model of the vertical hydrostatic guideway system built in this study can be used to predict the thermal deformation of worktable at center point at any running conditions. At a sliding feed rate of 1 m/s, the thermal positioning error of worktable at center point was 0.1539 µm in the X direction, 0.0009 µm in the Y direction and 2.0246 µm in Z direction.