The radio-over-fiber (RoF) technology has been widely studied during the past decades to extend the wireless communication coverage by leveraging the low-loss and broad bandwidth advantages of the optical fiber. With the increasing need for wireless communications, using millimeter-waves (mm-wave) in wireless communications has become the recent trend and many attempts have been made to build high-throughput and robust mm-wave RoF systems during the past a few years. Whilst the RoF technology provides many benefits, it suffers from several fundamental limitations due to the analog optical link, including the fiber chromatic dispersion and nonlinear impairments. Various approaches have been proposed to address these limitations. In particular, machine learning (ML) algorithms have attracted intensive research attention as a promising candidate for handling the complicated physical layer impairments in RoF systems, especially the nonlinearity during signal modulation, transmission and detection. In this paper, we review recent advancements in ML techniques for RoF systems, especially those which utilize ML models as physical layer signal processors to mitigate various types of impairments and to improve the system performance. In addition, ML algorithms have also been widely adopted for highly efficient RoF network management and resource allocation, such as the dynamic bandwidth allocation and network fault detection. In this paper, we also review the recent works in these research domains. Finally, several key open questions that need to be addressed in the future and possible solutions of these questions are also discussed.
The optical wireless communication (OWC) system has been widely studied as a promising candidate for indoor high-speed wireless communications. In particular, the spatial diversity scheme has shown to be effective to improve the performance of OWC systems. However, the delay amongst multiple channels in this scheme may result in severe inter-symbol-interference (ISI) and degradations of the system performance. Recent studies have shown that the symbol decision schemes based on recurrent neural networks (RNNs) can mitigate the impact of delays. However, their performances are limited when the channel delays are long. In this paper, we propose a delay-tolerant indoor OWC system, which utilizes an attention-augmented long-short term memory (ALSTM) RNN decision scheme to handle long channel delays. A 10 Gb/s repetition-coded indoor OWC system with the proposed ALSTM RNN decision scheme is experimentally demonstrated. Compared with traditional OWC systems which add cyclic prefix (CP) /zero-postfix (ZP) to combat the impact of channel delays, the proposed system does not reduce the effective data rate or throughput. Compared with the previous study which adopts the vanilla RNN decision scheme, the proposed ALSTM RNN decision scheme can better learn dependencies amongst received symbols with the help of attention mechanism, especially amongst non-neighboring symbols. Hence, it is more robust against the ISI induced by long channel delays. Experimental results show that compared with the previously studied vanilla RNN, over one-order-of-magnitude bit-error-rate improvement is achieved when the channel delay is more than 4.7-symbol-period.
The millimeter-wave (mm-wave) radio-over-fiber (RoF) systems have been widely studied as promising solutions to deliver high-speed wireless signals to end users, and neural networks have been studied to solve various linear and nonlinear impairments. However, high computation cost and large amounts of training data are required to effectively improve the system performance. In this paper, we propose and demonstrate highly computation efficient convolutional neural network (CNN) and binary convolutional neural network (BCNN) based decision schemes to solve these limitations. The proposed CNN and BCNN based decision schemes are demonstrated in a 5 Gbps 60 GHz RoF system for up to 20 km fiber distance. Compared with previously demonstrated neural networks, results show that the bit error rate (BER) performance and the computation intensive training process are improved. The number of training iterations needed is reduced by about 50 % and the amount of required training data is reduced by over 30 %. In addition, only one training is required for the entire measured received optical power range over 3.5 dB in the proposed CNN and BCNN schemes, to further reduce the computation cost of implementing neural networks decision schemes in mm-wave RoF systems.
With the rapidly-developing high-speed wireless communications, the 60 GHz millimeter-wave frequency range and radio-over-fiber systems have been investigated as a promising solution to deliver mm-wave signals. Neural networks have been studied to improve the mm-wave RoF system performances at the receiver side by suppressing linear and nonlinear impairments. However, previous neural network studies in mm-wave RoF systems focus on the off-line implementation with high-end GPUs , which is not practical for low power-consumption, low-cost and limited computation platform applications. To solve this issue, we investigate neural network hardware accelerator implementations using the field programmable gate array (FPGA), taking advantage of the low power consumption, parallel computation capability, and reconfigurablity features of FPGA. Convolutional neural network (CNN) and binary convolutional neural network (BCNN) hardware accelerators are demonstrated. In addition, to satisfy the low-latency requirement in mm-wave RoF systems and to enable the use of low-cost compact FPGA devices, a novel inner parallel optimization method is proposed. Compared with the embedded processor (ARM Cortex A9) execution latency, the CNN/BCNN FPGA-based hardware accelerator reduces their latency by over 92%. Compared with non-optimized FPGA implementations, the proposed optimization method reduces the processing latency by over 44% for CNN and BCNN. Compared with the GPU implementation, the latency of CNN implementation with the proposed optimization method is reduced by 85.49%, while the power consumption is reduced by 86.91%. Although the latency of BCNN implementation with the proposed optimization method is larger compared with the GPU implementation, the power consumption is reduced by 86.14%. The FPGA-based neural network hardware accelerators provide a promising solution for mm-wave RoF systems.