Cumulative plastic production worldwide skyrocketed from about 2 million tonnes in 1950 to 8.3 billion tonnes in 2015, with 6.3 billion tonnes (76%) ending up as waste. Of that waste, 79% is either in landfills or the environment. The purpose of the review is to establish the current global status quo in the plastics industry and assess the sustainability of some bio-based biodegradable plastics. This integrative and consolidated review thus builds on previous studies that have focused either on one or a few of the aspects considered in this paper. Three broad items to strongly consider are: Biodegradable plastics and other alternatives are not always environmentally superior to fossil-based plastics; less investment has been made in plastic waste management than in plastics production; and there is no single solution to plastic waste management. Some strategies to push for include: increasing recycling rates, reclaiming plastic waste from the environment, and bans or using alternatives, which can lessen the negative impacts of fossil-based plastics. However, each one has its own challenges, and country-specific scientific evidence is necessary to justify any suggested solutions. In conclusion, governments from all countries and stakeholders should work to strengthen waste management infrastructure in low- and middle-income countries while extended producer responsibility (EPR) and deposit refund schemes (DPRs) are important add-ons to consider in plastic waste management, as they have been found to be effective in Australia, France, Germany, and Ecuador.

Copper slag is generated when copper and nickel ores are recovered from their parent ores using a pyrometallurgical process, and these ores usually contain other elements which include iron, cobalt, silica, and alumina. Slag is a major problem in the metallurgical industries as it is dumped into heaps which have accumulated into millions of tons over the years. Moreover, they pose a danger to the environment as they occupy vacant land (space problems). Over the past few years, studies have been conducted to investigate the copper slag-producing outlets to learn their behavior, as well as properties of slag, to have the knowledge of how to better reuse and recycle copper slag. This review article provides the environmental and socioeconomic impacts of slag, as well as a characterization of copper slag, with the aim of reusing and recycling the slag to benefit the environment and economy. Recycling methods are considered an attractive technological pathway for reducing waste and greenhouse gas emissions, as well as promoting the concept of circular economy through the utilization of waste. These metal elements have value depending on their characteristics; hence, copper slag is considered as a secondary source of valuable metals. Some of the pyrometallurgical and hydrometallurgical processes to consider are physical separation, magnetic separation, flotation, leaching, and direct reduction roasting of iron (DRI). Some of the possible metals that can be recovered from the copper slag include Cu, Fe, Ni, Co, and Ag (precious metals).

Lead is a heavy metal that is bio accumulative and non-biodegradable that poses a threat to our health when it exists in excess in our bloodstream. It has found its way into wastewater from mostly chemical industrial processes. In this article, we investigated the adsorption and hence removal of lead (II) ions from wastewater in order to purify it for re-use in industrial processes or for plant and animal use. We synthesized nano silica hollow spheres (NSHS) and used them as adsorbents to remove lead ions from wastewater. When we characterized the NSHS using X-Ray diffraction, the amorphous nature of silica was evident with average crystal size of 39.5 nm. Scanning electron microscopy was used to determine the morphology of the adsorbent and the particles were found to be spherical in shape within a size range of 100–200 nm. Thermogravimetric analysis was used to determine the mass loss of NSHS which was ~2% at 800 °C. Our experimental results from adsorption studies showed that there was a linear relationship between temperature (27–60 °C) and adsorption efficiency and an inverse relationship between initial metal concentration (50–300 mg/L) and adsorption efficiency. At a maximum temperature of 60 °C and maximum initial metal concentration of 300 mg/L, the adsorption capacity was 200 mg/g and 262 mg/g, respectively while the adsorption efficiency was 99.6% and 87.4%, respectively. Our equilibrium and thermodynamic results revealed that the process was better modelled by the Langmuir adsorption isotherm (qmax = 266.89 mg/g and b = 0.89 L/mg). The adsorption process was both endothermic (ΔH = 97 kJ/mol) and spontaneous (ΔG = -22 kJ/mol). We can conclude that we were able to successfully synthesize NSHS, use them to remove lead (II) ions and the produced NSHS have a capacity that is higher than most other adsorbents investigated by other researchers.

The beneficiation of low-grade iron ores is a key research and development topic in the mineral processing industry. The gradual exhaustion of high-grade iron ore reserves, and rising consumer iron and steel demand globally necessitate efficient low-quality iron ore beneficiation to meet steelmaking quality requirements. This comprehensive review explores various beneficiation techniques for low-quality iron ore, focusing on conventional methods including comminution, froth flotation and gravity separation. This article discusses the principles, processes, and equipment used in these techniques and highlights recent advancements and research efforts in the field. This review also emphasizes the importance of effective beneficiation processes in enhancing economic viability, sustainable resource management, and environmental conservation. Furthermore, it presents a case study of iron ore deposits in Botswana, highlighting the potential economic growth and sustainable development that can be achieved by maximizing resource utilization through reductive roasting, followed by magnetic separation of iron ore using semi-bituminous coal as a reductant. Overall, this review provides valuable insights into low-grade iron ore beneficiation techniques and their significance in meeting the growing demand for high-quality iron and steel products.

Namibia Custom Smelters (NCS) process a range of copper concentrates in their three furnaces, namely; top submerged lance, copper converter and reverberatory furnaces, in order to produce mattes and fayalitic slags. The copper content of the slags range between 0.8 to 5 wt. % and this is considered too high for disposal to the environment. Currently, the slags are sent to a milling and flotation plant for liberation and recovery of residual copper. The copper recoveries realized in the plant are much lower than expected and it has been postulated that some copper minerals may be occurring in forms that are more difficult to float like oxides or fine disseminations in the gangue matrix. Mineralogical analysis of the slag samples was done using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) techniques. The analysis did not reveal the presence of copper oxide minerals, however most scans showed copper sulphide minerals as free grains and some finely disseminated in fayalite gangue. In the first phase of the present experimental studies, the slags were milled to 75% passing 45 microns, which is the degree of milling done in the existing plant mill-float circuit. A range of commercial flotation reagents that include xanthates, dithiophosphates, mercaptobenzothiazole, thionocarbamates, fatty acids, sulphides and sulphates were used in the flotation test-work. The copper recoveries obtained in the mill-float stage were between 70 - 80%. In the second phase of the study, the flotation tailings were further milled to 90% passing 45 microns and floated. The cumulative copper recoveries increased markedly to over 90%, which represents a significant improvement in comparison to the recoveries obtained from the mill-float process. Sodium alkyl dithiophosphate, mercaptobenzothiazole (FC7245) was found to be the secondary flotation reagent that gave the best copper recoveries.

Some of today’s modern life challenges include addressing the increased waste generation and energy deficiencies. Waste tyres have been identified as one of the key environmental concerns due to their non-biodegradable nature and bulk storage space demand. Pyrolysis is a thermochemical process with the potential to address the growing waste tyre problem, energy deficits, and material recovery by converting waste tyres to pyrolysis oil that can be used as a fuel. This study seeks to critically evaluate the feasibility of constructing and operating a waste tyre processing facility and then subsequently marketing and selling the pyrolysis secondary end products by developing a financial business model. The model encompasses costing, procurement, installation, commissioning, and operating a batch pyrolysis plant in Gauteng, South Africa. To achieve the study objectives, an order of magnitude costing method was used for model construction. The results showed the feasibility and sustainability of operating a 3.5 tonne per day batch waste tyre pyrolysis plant in Gauteng Province, South Africa, with a 15-year life span and a projected payback period of approximately 5 years. It was concluded that for the pyrolysis plant to be successful, further treatment steps are required to improve the process economics; also, a stable and sustainable product market should exist and be regulated in South Africa.