Single seismometer structure: Because of the lack of direct seismic observations, the interior structure of Mars has been a mystery. Khan et al. , Knapmeyer-Endrun et al. , and Stähler et al. used recently detected marsquakes from the seismometer deployed during the InSight mission to map the interior of Mars (see the Perspective by Cottaar and Koelemeijer). Mars likely has a 24- to 72-kilometer-thick crust with a very deep lithosphere close to 500 kilometers. Similar to the Earth, a low-velocity layer probably exists beneath the lithosphere. The crust of Mars is likely highly enriched in radioactive elements that help to heat this layer at the expense of the interior. The core of Mars is liquid and large, ∼1830 kilometers, which means that the mantle has only one rocky layer rather than two like the Earth has. These results provide a preliminary structure of Mars that helps to constrain the different theories explaining the chemistry and internal dynamics of the planet. Science , abf2966, abf8966, abi7730, this issue p. 434 , p. 438 , p. 443 see also abj8914, p. 388
Over the past few decades, the potential of collocated measurements of 6C data (3C of translational and 3C of rotational motion) has been demonstrated in global seismology using high-sensitivity, observatory-based ring laser technology. Proposed applications of 6C seismology range from tomographic reconstruction of near-receiver structure to the reduction of nonuniqueness in seismic source inverse problems. Applications to exploration problems have so far been hampered by the lack of appropriate sensors, but several applications have been proposed and demonstrated with array-derived rotational motion estimates. With the recent availability of, for example, fiber-optic-based high-sensitivity rotational motion sensors, widespread applications of 6C techniques to exploration problems are in sight. Potential applications are based on, for example, the fact that the extended set of combined translational and rotational motion observations enables carrying out array-type processing with single-station recordings such as wavefield separation and surface-wave suppression. Furthermore, measuring the rotational component (curl) of the seismic wavefield enables direct isolation of the S-wave constituents and could significantly improve S-wave exploration. Rotational measurements provide estimates of the spatial wavefield gradient at the free surface that allow carrying out analyses such as local slowness estimation and wavefield reconstruction. Furthermore, rotational motion measurements can help to resolve wavefield infidelity introduced by seismic instruments that are not well-coupled to the ground.
Interest in measuring displacement gradients, such as rotation and strain, is growing in many areas of geophysical research. This results in an urgent demand for reliable and field-deployable instruments measuring these quantities. In order to further establish a high-quality standard for rotation and strain measurements in seismology, we organized a comparative sensor test experiment that took place in November 2019 at the Geophysical Observatory of the Ludwig-Maximilians University Munich in Fürstenfeldbruck, Germany. More than 24 different sensors, including three-component and single-component broadband rotational seismometers, six-component strong-motion sensors and Rotaphone systems, as well as the large ring laser gyroscopes ROMY and a Distributed Acoustic Sensing system, were involved in addition to 14 classical broadband seismometers and a 160 channel, 4.5 Hz geophone chain. The experiment consisted of two parts: during the first part, the sensors were co-located in a huddle test recording self-noise and signals from small, nearby explosions. In a second part, the sensors were distributed into the field in various array configurations recording seismic signals that were generated by small amounts of explosive and a Vibroseis truck. This paper presents details on the experimental setup and a first sensor performance comparison focusing on sensor self-noise, signal-to-noise ratios, and waveform similarities for the rotation rate sensors. Most of the sensors show a high level of coherency and waveform similarity within a narrow frequency range between 10 Hz and 20 Hz for recordings from a nearby explosion signal. Sensor as well as experiment design are critically accessed revealing the great need for reliable reference sensors.
18 December 2017 in Geophysical Journal International
We provide a six component (6-C) polarisation model for P-, SV-, SH-, Rayleigh-, and Love-waves both inside an elastic medium as well as at the free surface. It is shown that single-station 6-C data comprised of three components of rotational motion and three components of translational motion provide the opportunity to unambiguously identify the wave type, propagation direction, and local P- and S-wave velocities at the receiver location by use of polarisation analysis. To extract such information by conventional processing of 3-component translational data would require large and dense receiver arrays. The additional rotational components allow the extension of the rank of the coherency matrix used for polarisation analysis. This enables us to accurately determine the wave type and wave parameters (propagation direction and velocity) of seismic phases, even if more than one wave is present in the analysis time window. This is not possible with standard, pure-translational 3-C recordings. In order to identify modes of vibration and to extract the accompanying wave parameters, we adapt the multiple signal classification algorithm (MUSIC). Due to the strong non-linearity of the MUSIC estimator function, it can be used to detect the presence of specific wave types within the analysis time window at very high resolution. We show how the extracted wavefield properties can be used, in a fully automated way, to separate the wavefield into its different wave modes using only a single 6-C recording station. As an example, we apply the method to remove surface wave energy while preserving the underlying reflection signal and to suppress energy originating from undesired directions, such as side-scattered waves.