Felix Bernauer

Dr. Felix Bernauer

Department of Earth and Environmental Sciences, Ludwig‐Maximilians‐University of Munich, Munich, Germany
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 January 2018 in Seismological Research Letters
Verified
Journal Article
Closed access
PDF file
FBFelix Bernauer
Felix Bernauer
JWJoachim Wassermann
Joachim Wassermann
FGFrederic Guattari
Frederic Guattari
AFArnaud Frenois
Arnaud Frenois
ABAlexandre Bigueur
Alexandre Bigueur
HIHeiner Igel
Heiner Igel
Recently, due to observations of rotational ground motions, a promising new field of research in seismology and engineering has developed. However, exploration of rotation’s potential has been hampered by the lack of a portable, reliable, and highly sensitive broadband rotational ground‐motion sensor. In this work, we present laboratory tests of the BlueSeis3A, the first commercially available fiber‐optic gyroscope specifically designed for applications in broadband seismology. Here, we estimate the sensor’s self‐noise level by means of power spectral density, operating range diagrams, and Allan deviation. Scale factor linearity is measured up to the largest likely rotation rates in seismology (⁠∼900  mrads−1⁠). Tests of the sensor’s susceptibility to changes in ambient conditions, such as temperature or magnetic field, demonstrate the BlueSeis3A’s reliability in field installations. Estimation of the orthogonality of the three sensor components completes our tests. We conclude that the BlueSeis3A is fit for a wide range of field applications in seismology, volcanology, ocean‐bottom observations, and earthquake engineering.

27 April 2018 in Geophysics
Verified
Journal Article
Open access
CSCedric Schmelzbach
Cedric Schmelzbach
SDStefanie Donner
Stefanie Donner
HIHeiner Igel
Heiner Igel
DSDavid Sollberger
David Sollberger
TTTaufiq Taufiqurrahman
Taufiq Taufiqurrahman
JRJohan O. A. Robertsson
Johan O. A. Robertsson
Over the past few decades, the potential of collocated measurements of 6C data (3C of translational and 3C of rotational motion) has been demonstrated in global seismology using high-sensitivity, observatory-based ring laser technology. Proposed applications of 6C seismology range from tomographic reconstruction of near-receiver structure to the reduction of nonuniqueness in seismic source inverse problems. Applications to exploration problems have so far been hampered by the lack of appropriate sensors, but several applications have been proposed and demonstrated with array-derived rotational motion estimates. With the recent availability of, for example, fiber-optic-based high-sensitivity rotational motion sensors, widespread applications of 6C techniques to exploration problems are in sight. Potential applications are based on, for example, the fact that the extended set of combined translational and rotational motion observations enables carrying out array-type processing with single-station recordings such as wavefield separation and surface-wave suppression. Furthermore, measuring the rotational component (curl) of the seismic wavefield enables direct isolation of the S-wave constituents and could significantly improve S-wave exploration. Rotational measurements provide estimates of the spatial wavefield gradient at the free surface that allow carrying out analyses such as local slowness estimation and wavefield reconstruction. Furthermore, rotational motion measurements can help to resolve wavefield infidelity introduced by seismic instruments that are not well-coupled to the ground.

3 January 2021 in Sensors
Verified
Journal Article
Open access
PDF file
FBFelix Bernauer
Felix Bernauer
KBKathrin Behnen
Kathrin Behnen
JWJoachim Wassermann
Joachim Wassermann
SESven Egdorf
Sven Egdorf
HIHeiner Igel
Heiner Igel
JBJohana Brokesova
Johana Brokesova
Interest in measuring displacement gradients, such as rotation and strain, is growing in many areas of geophysical research. This results in an urgent demand for reliable and field-deployable instruments measuring these quantities. In order to further establish a high-quality standard for rotation and strain measurements in seismology, we organized a comparative sensor test experiment that took place in November 2019 at the Geophysical Observatory of the Ludwig-Maximilians University Munich in Fürstenfeldbruck, Germany. More than 24 different sensors, including three-component and single-component broadband rotational seismometers, six-component strong-motion sensors and Rotaphone systems, as well as the large ring laser gyroscopes ROMY and a Distributed Acoustic Sensing system, were involved in addition to 14 classical broadband seismometers and a 160 channel, 4.5 Hz geophone chain. The experiment consisted of two parts: during the first part, the sensors were co-located in a huddle test recording self-noise and signals from small, nearby explosions. In a second part, the sensors were distributed into the field in various array configurations recording seismic signals that were generated by small amounts of explosive and a Vibroseis truck. This paper presents details on the experimental setup and a first sensor performance comparison focusing on sensor self-noise, signal-to-noise ratios, and waveform similarities for the rotation rate sensors. Most of the sensors show a high level of coherency and waveform similarity within a narrow frequency range between 10 Hz and 20 Hz for recordings from a nearby explosion signal. Sensor as well as experiment design are critically accessed revealing the great need for reliable reference sensors.

3 December 2020 in Sensors
Verified
Journal Article
Open access
PDF file
DSDavid Sollberger
David Sollberger
HIHeiner Igel
Heiner Igel
CSCedric Schmelzbach
Cedric Schmelzbach
PEPascal Edme
Pascal Edme
DMDirk-Jan van Manen
Dirk-Jan van Manen
JRJohan O. A. Robertsson
Johan O. A. Robertsson
Recent progress in rotational sensor technology has made it possible to directly measure rotational ground-motion induced by seismic waves. When combined with conventional inertial seismometer recordings, the new sensors allow one to locally observe six degrees of freedom (6DOF) of ground-motion, composed of three orthogonal components of translational motion and three orthogonal components of rotational motion. The applications of such 6DOF measurements are manifold—ranging from wavefield characterization, separation, and reconstruction to the reduction of non-uniqueness in seismic inverse problems—and have the potential to revolutionize the way seismic data are acquired and processed. However, the seismological community has yet to embrace rotational ground-motion as a new observable. The aim of this paper is to give a high-level introduction into the field of 6DOF seismology using illustrative examples and to summarize recent progress made in this relatively young field. It is intended for readers with a general background in seismology. In order to illustrate the seismological value of rotational ground-motion data, we provide the first-ever 6DOF processing example of a teleseismic earthquake recorded on a multicomponent ring laser observatory and demonstrate how wave parameters (phase velocity, propagation direction, and ellipticity angle) and wave types of multiple phases can be automatically estimated using single-station 6DOF processing tools. Python codes to reproduce this processing example are provided in an accompanying Jupyter notebook.

8 July 2020 in Seismological Research Letters
Verified
Journal Article
Closed access
PDF file
FBFelix Bernauer
Felix Bernauer
JWJoachim Wassermann
Joachim Wassermann
HIHeiner Igel
Heiner Igel
Inertial sensors like seismometers or accelerometers are sensitive to tilt motions. In general, from pure acceleration measurements, it is not possible to separate the tilt acceleration from the translational ground acceleration. This can lead to severe misinterpretation of seismograms. Here, we present three different methods that can help solving this problem by correcting translational records for dynamic tilt induced by ground deformation with direct measurements of rotational motions: (1) a simple time-domain method, (2) a frequency-domain method proposed by Crawford and Webb (2000) using a coherence-weighted transfer function between rotation and acceleration, and (3) an adapted frequency-domain method that corrects only those parts of the spectrum with coherence between translational acceleration and rotation angle higher than 0.5. These three methods are discussed in three different experimental settings: (1) a reproducible and precisely known laboratory test using a high-precision tilt table, (2) a synthetic test with a simulated volcanic very-long-period event, and (3) a real data set recorded during the 2018 Mt. Kīlauea caldera collapse. All the three test cases show severe influence of tilt motion on the acceleration measurements. The time-domain method and the adapted frequency-domain method show very similar performance in all three test cases. Those two methods are able to remove the tilt component reliably from the acceleration record.

28 February 2020 in Geophysical Research Letters
Verified
Journal Article
Open access
PDF file
JWJ. Wassermann
J. Wassermann
FBFelix Bernauer
Felix Bernauer
BSB. Shiro
B. Shiro
IJI. Johanson
I. Johanson
FGF. Guattari
F. Guattari
HIHeiner Igel
Heiner Igel
Near‐field recordings of large earthquakes and volcano‐induced events using traditional seismological instrumentation often suffer from unaccounted effects of local tilt and saturation of signals. Recent hardware advances have led to the development of the blueSeis‐3A, a very broadband, highly sensitive rotational motion sensor. We installed this sensor in close proximity to permanently deployed classical instrumentation (i.e., translational seismometer, accelerometer, and tiltmeter) at the Hawaiian Volcano Observatory (USGS). There, we were able to record three ~Mw 5 earthquakes associated with large collapse events during the later phase of the 2018 Kīlauea summit eruption. Located less than 2 km from the origins of these sources, the combined six‐axis translational and rotational measurements revealed clear static rotations around all three coordinate axes. With these six component recordings, we have been able to reconstruct the complete time history of ground motion of a fixed point during an earthquake for the first time.