Roberto Serrano-López

Dr. Roberto Serrano-López

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

30 August 2023 in Environmental Science and Pollution Research
Verified
Journal Article
Open access
PDF file
AEAna Belén Espinosa
Ana Belén Espinosa
VRVíctor Revilla-Cuesta
Víctor Revilla-Cuesta
MSMarta Skaf
Marta Skaf
RSRoberto Serrano-López
Roberto Serrano-López
VOVanesa Ortega-López
Vanesa Ortega-López
In this paper, the performance of ladle furnace slag (LFS), a by-product of secondary steel refining, is evaluated as a binder to stabilize clayey soils of low bearing capacity. The aim is to define whether additions of this by-product to clayey soil can stabilize the soil in accordance with the technical specifications of Spanish standards. To do so, three different soils stabilized with 5% LFS were compared with the same soils stabilized with 2% lime and with no stabilization, in order to investigate their different behaviors. The chemical and mineralogical characterizations of all the soil mixes were conducted using X-ray fluorescence, X-ray diffraction, and scanning electron microscopy. The Atterberg limit test was used to study the plastic behavior of the soils, and the results of compaction, bearing capacity, unconfined compressive strength, and direct shear strength (cohesion and friction angle) tests defined their strength characteristics. The analysis was completed with the pH monitoring of the mixes along the curing time in order to relate the pH changes with the strength evolution. The addition of LFS to the soils has resulted in an increase in the liquid limit and plastic limit, causing therefore a slight decrease in the plasticity index. All the soils showed increases between 30% and 70% in their California Bearing Ratios immediately after mixing with 5% LFS, and after 90 days of curing, improvements of 30–188% in their unconfined compressive strength were noted in comparison with untreated soil, which were higher than the lime-stabilized soils. The cohesion of soils stabilized with LFS at 28 days of curing obtained improvements ranging from 40 to 300% depending on the type of soil. However, the friction angle showed a slight increase of 10% in two of the soils and zero in another. The high initial pH in LFS-stabilized soils was maintained during the curing time, which favored the development of pozzolanic reactions that improve the soil strength. These results confirmed that the substitution of lime with LFS is a feasible option for soil stabilization.

13 December 2023 in Buildings
Verified
Journal Article
Open access
PDF file
VRVíctor Revilla-Cuesta
Víctor Revilla-Cuesta
RSRoberto Serrano-López
Roberto Serrano-López
AEAna Belén Espinosa
Ana Belén Espinosa
VOVanesa Ortega-López
Vanesa Ortega-López
MSMarta Skaf
Marta Skaf
The addition of Ladle Furnace Slag (LFS) to concrete modifies its compressive strength and modulus of elasticity and consequently impacts their relationship. This research evaluated both properties at 28, 90, and 180 days in concrete mixes produced with 5%, 10%, and 20% of two LFS types, both stabilized and non-stabilized. The relationship between them was then analyzed through these experimental results by adopting a statistical approach. A three-way analysis of variance revealed that both properties were affected by LFS differently. Thus, the effect of each LFS content on both features varied depending on its composition and pre-treatment. Furthermore, the effect of the LFS content on the compressive strength was also influenced by the age of the concrete. These facets implied that when analyzing the relationship between both mechanical properties, the monotonic correlations were stronger than the linear ones, reaching values between 0.90 and 1.00. Therefore, the double reciprocal regression models were the most precise ones for expressing the modulus of elasticity as a function of compressive strength. The model accuracy was further enhanced when discriminating based on the LFS type and introducing concrete age as a predictive variable. With all these considerations, the average deviations between the estimated and experimental values of 1–3% and the maximum deviations of 4–7% were reached, as well as R2 coefficients of up to 97%. These aspects are central to the further development of LFS concrete models.

23 December 2024 in Materials
Verified
Journal Article
Open access
PDF file
VRVíctor Revilla-Cuesta
Víctor Revilla-Cuesta
AEAna Belén Espinosa
Ana Belén Espinosa
RSRoberto Serrano-López
Roberto Serrano-López
MSMarta Skaf
Marta Skaf
Juan Manuel Manso VillalaínJuan Manuel Manso Villalaín
Juan Manuel Manso Villalaín
The glass fiber-reinforced polymer (GFRP) materials of wind turbine blades can be recovered and recycled by crushing, thereby solving one of the most perplexing problems facing the wind energy sector. This process yields selectively crushed wind turbine blade (SCWTB), a novel waste that is almost exclusively composed of GFRP composite fibers that can be revalued in terms of their use as a raw material in concrete production. In this research, the fresh and mechanical performance of concrete made with 1.5%, 3.0%, 4.5%, and 6.0% SCWTB is studied. Once incorporated into concrete mixes, SCWTB waste slightly reduced slumps due to the large specific surface area of the fibers, and the stitching effect of the fibers on mechanical behavior was generally adequate, as scanning electron microscopy demonstrated good fiber adhesion within the cementitious matrix. Thus, despite the increase in the content of water and plasticizers when adding this waste to preserve workability, the compressive strength only decreased in the long term with the addition of 6.0% SCWTB, a value of 45 MPa always being reached at 28 days; Poisson’s coefficient remained constant from 3.0% SCWTB; splitting tensile strength was maintained at around 4.7 MPa up to additions of 3.0% SCWTB; and the flexural strength of mixes containing 6.0% and 1.5% SCWTB was statistically equal, with a value near 6.1 MPa. Furthermore, all mechanical properties of the concrete except for flexural strength were improved with additions of SCWTB compared to raw crushed wind turbine blade, which apart from GFRP composite fibers contains approximately spherical polymer and balsa wood particles. Flexural strength was conditioned by the proportion of fibers, their dimensions, and their strength, which were almost identical for both waste types. SCWTB would be preferable for applications in which compression stresses predominate.

2 November 2021 in PFG – Journal of Photogrammetry, Remote Sensing and Geoinformation Science
Verified
Journal Article
Open access
PDF file
ABAmparo Bernal
Amparo Bernal
CMCarlos Muñoz
Carlos Muñoz
ASAna Sáez
Ana Sáez
RSRoberto Serrano-López
Roberto Serrano-López
The possibility of accessing free cartographic resources on the internet instead of creating their own digital object representation is a big advantage for architecture and engineering professionals in the surveying process of a construction or restoration project. The use of these products must be carried out with the guarantee that the precision of the site representation made from them is adapted to the level of detail required by each phase of the project. This paper compares graphically and statistically the accuracy of the topographic surfaces we can get from the LIDAR point clouds and the Digital Terrain Models (DTMs) of the National Centre for Geographic Information (CNIG by its Spanish acronym) that in Spain are available on the internet free of charge. We will use as a reference surface for comparison, the topographic map of the Digital Model Elevation (DEM) from the images captured by an unmanned aerial vehicle (UAV) processed with software based on algorithms of Structure from Motion (SfM). The study case for this comparative research will be the graphical survey of an archaeological site of funerary architecture made in 1939 during the Spanish Civil War. The monument is located near the city of Burgos (Spain) in an area with difficult access and restricted airspace, which makes difficult the fieldwork. The modeling of the surface has great importance for the graphic survey of the site, because its architectural configuration is adapted to the steep slope of the hillside. The purpose of this research is to check, if the surfaces provided through the Spanish open public cartographic resources are accurate enough to replace the mapping from UAV photogrammetry. Finally, if the outcomes can be extrapolated for widespread use of these resources for the site modeling of a project, according to the requirements of the different levels of development defined in the Building Information Modeling (BIM) methodology.

30 March 2017 in Informes de la Construcción
Verified
Journal Article
Open access
JUJ. R. Urruchi-Rojo
J. R. Urruchi-Rojo
JMJ. A. Martínez-Martínez
J. A. Martínez-Martínez
RSRoberto Serrano-López
Roberto Serrano-López
La forma de las bóvedas de los puentes de piedra ha ido evolucionando con el tiempo, existiendo bibliografía en la que además de recomendarse una tipología frente a otra, según la época, se prescribía la manera de ejecutar el relleno del trasdós. Todo ello surgía en un principio como fruto de las experiencias adquiridas durante la construcción y observación de los puentes. Así fueron emergiendo, a partir del siglo xviii, formulaciones que en unos casos aportaban un resultado y en otros el contrario. Este artículo pretende realizar una comparación entre varias de estas formulaciones, así como efectuar un análisis de la influencia en la variación de la carga de rotura, tanto del rebajamiento de la bóveda como de la participación del relleno rígido en el trasdós del mismo.