Green Deep Eutectic Solvents (DESs) are considered here as an alternative to conventional organic solvents and ionic liquids (IL) for the extraction of phenolic compounds from pyrolysis oil. Although ionic liquids have shown a promising future in extraction processes, DESs possess not only most of their remarkable physico-chemical properties, but are also cheaper, easier to prepare and non-toxic, increasing the infatuation with these new moieties to the detriment of ionic liquids. In this work, phenol was selected as a representative of phenolic compounds, and toluene and heptane were used to model the pyrolysis oil. COSMO-RS was used to investigate the interaction between the considered Dess, phenol, n-heptane, and toluene. Two DESs (one ammonium and one phosphonium based) were subsequently used for experimental liquid–liquid extraction. A ternary liquid–liquid equilibrium (LLE) experiment was conducted with different feed concentrations of phenol ranging from 5 to 25 wt% in model oil at 25 °C and at atmospheric pressure. Although both DESs were able to extract phenol from model pyrolysis oil with high distribution ratios, the results showed that ammonium-based DES was more efficient than the phosphonium-based one. The composition of phenol in the raffinate and extract phases was determined using gas chromatography. A similar trend was observed by the COSMO-RS screening for the two DESs.
1 February 2018 in Journal of Chemical & Engineering Data
Deep eutectic solvents (DESs) are green solvents developed as an alternative to conventional organic solvents and ionic liquids to extract nitrogen compounds from fuel oil. DESs based on p-toluenesulfonic acid (PTSA) are a new solvent class still under investigation for extraction/separation. This study investigated a new DES formed from a combination of tetrabutylphosphonium bromide (TBPBr) and PTSA at a 1:1 molar ratio. Two sets of ternary liquid–liquid equilibrium experiments were performed with different feed concentrations of nitrogen compounds ranging up to 20 mol% in gasoline and diesel model fuel oils. More than 99% of quinoline was extracted from heptane and pentadecane using the DES, leaving the minutest amount of the contaminant. Selectivity was up to 11,000 for the heptane system and up to 24,000 for the pentadecane system at room temperature. The raffinate phase’s proton nuclear magnetic resonance (1H-NMR) spectroscopy and GC analysis identified a significantly small amount of quinoline. The selectivity toward quinoline was significantly high at low solute concentrations. The root-mean-square deviation between experimental data and the non-random two-liquid (NRTL) model was 1.12% and 0.31% with heptane and pentadecane, respectively. The results showed that the TBPBr/PTSADES is considerably efficient in eliminating nitrogen compounds from fuel oil.
In the present study, the ability for novel carbon microspheres (CMs) derived from date palm (Phoenix dactylifera) biomass using a hydrothermal carbonization (HTC) process and activated using phosphoric acid to remove methylene blue dye was investigated. Three types of palm-based wastes (seeds, leaflet, and inedible crystallized date palm molasses) were used and converted to CMs via the HTC process. The prepared samples were then activated using phosphoric acid via the incipient wetness impregnation method. The CMs samples before and after activation were analyzed using scanning electron microscopy (SEM), elemental analysis and scanning (CHNS), and the Fourier transform infrared (FTIR) and Brunauer–Emmet–Teller (BET) methods. The samples exhibited high BET surface areas after activation (1584 m2/g). The methylene blue adsorption results showed good fitting to the Langmuir, Fruendlich, and Temkin isotherm models for all activated samples. The maximum adsorption capacity achieved was 409.84 mg/g for activated CM obtained from the palm date molasses, indicating its high potential for application as a dye-based adsorption material.
Due to their toxicity and persistence in the environment, phenolic pollutants pose a serious threat to the ecosystem. In this work, the performance of hydrophobic deep eutectic solvents (HDESs) for phenol removal from aqueous effluents is thoroughly investigated using COSMO-RS screening followed by experimental validation. The screening results of 73 HDESs showed that the efficacy of phenol removal is significantly affected by chain length, functional groups, and aromaticity. Trioctylphosphine oxide (TOPO)-based HDESs were found to be the most effective HDESs for phenol elimination combined either with menthol (Men), 1-hexanol (Hex), Decanoic acid (DecA), or Thymol (Thy) all in 1:1 molar ratios. The better phenol elimination abilities of the selected HDESs were confirmed by experimental LLE data obtained at 298.15 K and 101 kPa. In fact, it has been found that there is a positive correlation between extraction efficiency and phenol content. For instance, at a phenol concentration of 7%, TOPO:Men had the highest extraction efficiency (96%). Moreover, the physicochemical properties of the selected HDESs, such as density, viscosity, FTIR, 1HNMR, and TGA, were also measured. The results showed their high thermal stability and low water solubility, which makes them suitable for phenol extraction applications. This study shows that HDESs are capable of removing phenolic contaminants from aqueous effluents in a sustainable and efficient manner and that the selected TOPO-based HDESs are of particular interest for further research and application in phenol removal.
In this study, a new epoxidized oil from Citrullus colocynthis seed oil (CCSO) was obtained for a potential application in the formulation of polyurethane coatings. Initially, the fatty acid composition of CCSO was determined by gas chromatography–mass spectrometry (GC–MS). Subsequently, the epoxidation of CCSO was performed with in situ generated peracetic acid, which was formed with hydrogen peroxide (30 wt.%) and glacial acetic acid and catalyzed with sulfuric acid. The reaction was continued at a molar ratio of 1.50:1.0 of hydrogen peroxide to double bond (H2O2:DB) for 6 h at a controlled temperature of 60 °C. The resulting epoxidized oil was then used to produce a bio-based polyol by hydroxylation. The molar ratio of epoxy groups to methanol and distilled water was maintained at 1:11:2, and the reaction was carried out for 2 h at a controlled temperature of 65 °C. The major functional groups of the epoxidized oil and its polyol were validated by Fourier-transform infrared (FT-IR) and proton nuclear magnetic resonance (1H NMR) spectroscopies. A polyurethane (PU) coating was produced from the synthesized polyol and 3HDI isocyanurate, keeping the molar ratio of NCO:OH at 1:1. The resulting PU coating was then applied to glass and aluminum panels (Al 1001). After the film was cured, the properties of the PU coating were evaluated using various techniques including pencil hardness, pendulum hardness, adhesion, gloss, chemical resistance, and EIS tests. The results show that the PU coating obtained from CCSO is a promising new raw material for coating applications.