A hybrid microgrid-powered charging station reduces transmission losses with better power flow control in the modern power system. However, the uncoordinated charging of battery electric vehicles (BEVs) with the hybrid microgrid results in ineffective utilization of the renewable energy sources connected to the charging station. Furthermore, planned development of upcoming charging stations includes a multiport charging facility, which will cause overloading of the utility grid. The paper analyzes the following technical issues: (1) the energy management strategy and converter control of multiport BEV charging from a photovoltaic (PV) source and its effective utilization; (2) maintenance of the DC bus voltage irrespective of the utility grid overloading, which is caused by either local load or the meagerness of PV power through its energy storage unit (ESU). In addition, the charge controller provides closed loop charging through constant current and voltage, and this reduces the charging time. The aim of an energy management strategy is to minimize the usage of utility grid power and store PV power when the vehicle is not connected for charging. The proposed energy management strategy (EMS) was modeled and simulated using MATLAB/Simulink, and its different modes of operation were verified. A laboratory-scale experimental prototype was also developed, and the performance of the proposed charging station was investigated.
The capacitive coupled wireless power transfer (CCWPT) operating at megahertz (MHz) frequency is broadly considered as the promising solution for low power biomedical implants. The class E power amplifier is attractive in MHz range wireless power transfer (WPT) applications due to zero voltage switching (ZVS) and zero voltage derivative switching (ZVDS) properties. The existing design of class E amplifier is investigated only for inductive resonant coupled (IRC) WPT systems; the modelling and optimization of the class E amplifier for CCWPT systems are not deliberated with load variation. Meanwhile, the variations in the coupling distance and load are common in real time applications, which could reduce the power amplifier (PA) efficiency. The purpose of this paper is to model and optimize the class E amplifier for CCWPT systems used in MHz range applications. The analytical model of PA parameters and efficiency are derived to determine the optimal operating conditions. Also, an inductive-capacitive-inductive (LCL) impedance matching network is designed for the robust operation of the PA, which improves the efficiency and maintains required impedance compression. The maximum efficiency of the proposed design reached up to 96.34% at 13.56 MHz and the experimental results are closely matched with the simulation.
Simultaneous power transfer to multiple receiver (Rx) system is one of the key advantages of wireless power transfer (WPT) system using magnetic resonance. However, determining the optimal condition to uniformly transfer the power to a selected Rx at high efficiency is the challenging task under the dynamic environment. The cross-coupling and frequency splitting are the dominant issues present in the multiple Rx dynamic WPT system. The existing analysis is performed by considering any one issue present in the system; on the other hand, the cross coupling and frequency splitting issues are interrelated in dynamic Rx’s, which requires a comprehensive design strategy by considering both the problems. This paper proposes an optimal design of multiple Rx WPT system, which can eliminate cross coupling, frequency splitting issues and increase the power transfer efficiency (PTE) of selected Rx. The cross-coupling rejection, uniform power transfer is performed by adding an additional relay coil and independent resonance frequency tuning with capacitive compensation to each Rx unit. The frequency splitting phenomena are eliminated using non-identical transmitter (Tx) and Rx coil structure which can maintain the coupling between the coil under the critical coupling limit. The mathematical analysis of the compensation capacitance calculation and optimal Tx coil size identification is performed for the four Rx WPT system. Finite element analysis and experimental investigation are carried out for the proposed design in static and dynamic conditions.
The exhaust gases from various sources cause air pollution, which is a leading contributor to the global disease burden. Hence, it has become vital to monitor and control the increasing pollutants coming out of the various sources into the environment. This paper has designed and developed a sensor material to determine the amount of carbon monoxide (CO), which is one of the major primary air pollutants produced by human activity. Nanoparticle-based sensors have several benefits in sensitivity and specificity over sensors made from traditional materials. In this study, tin oxide (SnO2), which has greater sensitivity to the target gas, is selected as the sensing material which selectively senses only CO. Tin oxide nanoparticles have been synthesized from stannous chloride dihydrate chemical compound by chemical precipitation method. Palladium, at the concentration of 0.1%, 0.2%, and 0.3% by weight, was added to tin oxide and the results were compared. Synthesized samples were characterized by X-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) techniques. XRD revealed the tetragonal structure of the SnO2 nanoparticles and FESEM analysis showed the size of the nanoparticles to be about 7–20 nm. Further, the real-time sensor testing was performed and the results proved that the tin oxide sensor, doped with 0.2% palladium, senses the CO gas more efficiently with greater sensitivity.