This paper provides a methodology for the prediction of fracture loads in additively manufactured ABS material containing U-notches. The approach is based on the Average Strain Energy Density (ASED) criterion, which assumes that the material being analysed develops fully linear-elastic behaviour. Thus, in those cases where the material has a certain (non-negligible) amount of non-linear behaviour, the ASED criterion needs to be corrected. In this sense, in this paper, the ASED criterion is also combined with the Equivalent Material Concept (EMC) and the Fictitious Material Concept (FMC), both being corrections in which the non-linear real material is substituted by a linear equivalent or fictitious material, respectively. The resulting methodologies have been applied to additively manufactured ABS U-notched single-edge-notched bending (SENB) specimens combining five different notch radii (0, 0.25, 0.5, 1 and 2 mm) and three different raster orientations (0/90, 45/−45 and 30/−60). The results obtained demonstrate that both the ASED-EMC and the ASED-FMC combined criteria provide more accurate predictions than those obtained directly through the ASED criterion, with the ASED-EMC criterion generally providing safe more accurate predictions, with an average deviation from the experimental fracture loads between +1.0% (predicted loads higher than experimental loads) and −7.6% (predicted loads lower than experimental loads).
Modern society demands more sustainable and economical construction elements. One of the available options for manufacturing this type of element is the valorisation of end-of-life waste, such as, for example, the recycling of polymers used in industry. The valorisation of these wastes reduces costs and avoids the pollution generated by their landfill disposal. With the aim of helping to obtain this type of material, this work describes a methodology for recycling polyethylene for the manufacture of fibres that will later be used as reinforcement for structural concrete. These fibres are manufactured using an injection moulding machine. Subsequently, their physical and mechanical properties are measured and compared with those of the material before it is crushed and injected. The aim of this comparison is to evaluate the recycling process and analyse the reduction of the physical-mechanical properties of the recycled polyethylene in the process. Finally, to determine the properties of the fibre concrete, three types of concrete were produced: a control concrete, a reinforced concrete with 2 kg/m3 of fibres, and a reinforced concrete with 4 kg/m3 of fibres. The results show an enhancement of mechanical properties when the fibres are incorporated, particularly the tensile strength; and they also show excellent performance controlling cracking in concrete.
This paper analyses the notch effect in the fracture behaviour of acrylonitrile–styrene–acrylate (ASA) material manufactured by fused filament fabrication (FFF). The research is performed on 72 single-edge-notch bending (SENB) specimens containing U-notches with nominal notch radii varying from 0 mm (crack-like defects) up to 2.0 mm, and fabricated with three different raster orientations (0/90, 45/−45, 30/−60). Apparent fracture toughness values are obtained for the different conditions and the resulting notch effect is analysed through the Theory of Critical Distances. A fractographic analysis is also performed using Scanning Electron Microscopy (SEM) in order to justify the fracture (macroscopic) behaviour from the observed fracture micromechanisms. The notch effect observed in the three ASA raster orientations is very similar, and lower than that observed in other FFF polymeric alternatives (ABS, PLA).
This paper attempts to validate the application of the Virtual Isotropic Material Concept (VIMC) in combination with the average strain energy density (ASED) criterion to predict the critical load in notched laminated composites. This methodology was applied to E/glass–epoxy-laminated composites containing U-notches. For this purpose, a series of fracture test data recently published in the literature on specimens with different notch tip radii, lay-up configurations, and a number of plies were employed. It was shown that the VIMC–ASED combined approach provided satisfactory predictions of the last-ply failure (LPF) loads (i.e., critical loads).
This paper validates a methodology for the estimation of critical loads in tubular beams containing notch-type defects. The methodology is particularized for the case of Al6060-T66 tubular cantilever beams containing U-shaped notches. It consists in obtaining the stress field at the notch tip using finite element analysis (FEA) and the subsequent application of the theory of critical distances (TCD) to derive the corresponding critical load (or load-bearing capacity). The results demonstrate that this methodology provides satisfactory predictions of fracture loads.