Remote sensing technologies have seen extraordinary improvements in both spatial resolution and accuracy recently. In particular, airborne laser scanning systems can now provide data for surface modeling with unprecedented resolution and accuracy, which can effectively support the detection of sub-meter surface features, vital for landslide mapping. Also, the easy repeatability of data acquisition offers the opportunity to monitor temporal surface changes, which are essential to identifying developing or active slides. Specific methods are needed to detect and map surface changes due to landslide activities. In this paper, we present a methodology that is based on fusing probabilistic change detection and landslide surface feature extraction utilizing multi-temporal Light Detection and Ranging (LiDAR) derived Digital Elevation Models (DEMs) to map surface changes demonstrating landslide activity. The proposed method was tested in an area with numerous slides ranging from 200 m2 to 27,000 m2 in area under low vegetation and tree cover, Zanesville, Ohio, USA. The surface changes observed are probabilistically evaluated to determine the likelihood of the changes being landslide activity related. Next, based on surface features, a Support Vector Machine (SVM) quantifies and maps the topographic signatures of landslides in the entire area. Finally, these two processes are fused to detect landslide prone changes. The results demonstrate that 53 out of 80 inventory mapped landslides were identified using this method. Additionally, some areas that were not mapped in the inventory map displayed changes that are likely to be developing landslides.
15 February 2020 in International Journal of Remote Sensing
The ability to accurately estimate the amount of stockpile material for construction projects can have a substantial impact on project budgets and schedules as well as public safety. Recent proliferation of small Unmanned Aircraft System (sUAS) platforms has made it possible to estimate these stockpiles using inexpensive aerial imagery and photogrammetry at a fraction of the cost and time compared to traditional methods. This study examines the quality of height and volume estimates from sUAS photogrammetry processed through Agisoft Metashape, Bentley ContextCapture, and PixElement, and compared with Global Navigation Satellite System (GNSS) based surveying and Terrestrial Laser Scanning (TLS) measurements. Measurements made on three co-located stockpiles occupying in total 345 m2 and a volume of 487.11 m3 showed that all three software produced results within 3% of TLS measured height and 2% of TLS volume overall, with greater local variation. Moreover, photogrammetry provided complete coverage while the TLS data had voids due to scanner obstructions. Considering that results could be further improved with refinements in technique, this study joins others in demonstrating that sUAS photogrammetry provides a viable alternative to conventional methods for estimating stockpiles.
Interest in small unmanned aircraft systems (sUAS) for topographic mapping has significantly grown in recent years, driven in part by technological advancements that have made it possible to survey small- to medium-sized areas quickly and at low cost using sUAS aerial photography and digital photogrammetry. Although this approach can produce dense point clouds of topographic measurements, they have not been tested extensively to provide insights on accuracy levels for topographic mapping. This case study examines the accuracy of a sUAS-derived point cloud of a parking lot located at the Citizens Bank Arena (CBA) in Ontario, California, by comparing it to ground control points (GCPs) measured using global navigation satellite system (GNSS) data corrected with real-time kinematic (RTK) and to data from a terrestrial laser scanning (TLS) survey. We intentionally chose a flat surface due to the prevalence of flat scenes in sUAS mapping and the challenges they pose for accurately deriving vertical measurements. When the GNSS-RTK survey was compared to the sUAS point cloud, the residuals were found to be on average 18 mm and −20 mm for the horizontal and vertical components. Furthermore, when the sUAS point cloud was compared to the TLS point cloud, the average difference observed in the vertical component was 2 mm with a standard deviation of 31 mm. These results indicate that sUAS imagery can produce point clouds comparable to traditional topographic mapping methods and support other studies showing that sUAS photogrammetry provides a cost-effective, safe, efficient, and accurate solution for topographic mapping.
Traditional acquisition methods for generating digital surface models (DSMs) of infrastructure are either low resolution and slow (total station-based methods) or expensive (LiDAR). By contrast, photogrammetric methods have recently received attention due to their ability to generate dense 3D models quickly for low cost. However, existing frameworks often utilize many manually measured control points, require a permanent RTK/PPK reference station, or yield a reconstruction accuracy too poor to be useful in many applications. In addition, the causes of inaccuracy in photogrammetric imagery are complex and sometimes not well understood. In this study, a small unmanned aerial system (sUAS) was used to rapidly image a relatively even, 1 ha ground surface. Model accuracy was investigated to determine the importance of ground control point (GCP) count and differential GNSS base station type. Results generally showed the best performance for tests using five or more GCPs or when a Continuously Operating Reference Station (CORS) was used, with vertical root mean square errors of 0.026 and 0.027 m in these cases. However, accuracy outputs generally met comparable published results in the literature, demonstrating the viability of analyses relying solely on a temporary local base with a one hour dwell time and no GCPs.
Landslides are natural disasters that cause extensive environmental, infrastructure and socioeconomic damage worldwide. Since they are difficult to identify, it is imperative to evaluate innovative approaches to detect early-warning signs and assess their susceptibility, hazard and risk. The increasing availability of airborne laser-scanning data provides an opportunity for modern landslide mapping techniques to analyze topographic signature patterns of landslide, landslide-prone and landslide scarred areas over large swaths of terrain. In this study, a methodology based on several feature extractors and unsupervised classification, specifically k-means clustering and the Gaussian mixture model (GMM) were tested at the Carlyon Beach Peninsula in the state of Washington to map slide and non-slide terrain. When compared with the detailed, independently compiled landslide inventory map, the unsupervised methods correctly classify up to 87% of the terrain in the study area. These results suggest that (1) landslide scars associated with past deep-seated landslides may be identified using digital elevation models (DEMs) with unsupervised classification models; (2) feature extractors allow for individual analysis of specific topographic signatures; (3) unsupervised classification can be performed on each topographic signature using multiple number of clusters; (4) comparison of documented landslide prone regions to algorithm mapped regions show that algorithmic classification can accurately identify areas where deep-seated landslides have occurred. The conclusions of this study can be summarized by stating that unsupervised classification mapping methods and airborne light detection and ranging (LiDAR)-derived DEMs can offer important surface information that can be used as effective tools for digital terrain analysis to support landslide detection.
26 July 2022 in Transportation Research Record: Journal of the Transportation Research Board
Parking space management systems help organize and optimize available parking spaces for consumers, making the process of finding and using parking spaces more efficient. Current parking space management systems include manual recognition, the employment of magnetic and ultrasonic sensors, and, recently, computer vision (CV). One relatively new region-based convolutional neural network (R-CNN) model, Mask R-CNN, has shown promise in its ability to detect objects and has demonstrated superior performance over many other popular CV methods. Building on Mask R-CNN, an updated version, Rotated Mask R-CNN, which can generate bounding boxes the axes of which are rotated with respect to the image’s axis, was proposed to address the limitation of Mask R-CNN. Albeit with the documented theoretical benefits, the application of the rotated version is rare because of its recent invention. To this end, the study aims to detect vehicle instances in one parking lot using various Rotated Mask R-CNN models based on unmanned aircraft system collected images. Both average precision and average recall were utilized to assess the performance of the alternative models with different backbone and head networks. The results reveal the high accuracy level associated with Rotated Mask R-CNN in real-time detection of vehicles. In addition, the results indicate that the inference speed and total loss are highly correlated with head networks and training schedules.