Hyun-su Seo

Mr. Hyun-su Seo


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2020 in Polymers
Verified
Journal Article
Open access
PDF file
HPHee-woong Park
Hee-woong Park
HSHyun-su Seo
Hyun-su Seo
KKKiok Kwon
Kiok Kwon
JLJung-Hyun Lee
Jung-Hyun Lee
SSSeunghan Shin
Seunghan Shin
To improve the heat resistance of acrylic-based pressure-sensitive adhesive (PSA), silicone-block-containing acrylic PSAs (SPSAs) were synthesized using a polydimethylsiloxane (PDMS)-based macro-azo-initiator (MAI). To evaluate the heat resistance of the PSA films, the probe tack and 90° peel strength were measured at different temperatures. The acrylic PSA showed that its tack curves changed from balanced debonding at 25 °C to cohesive debonding at 50 °C and exhibited a sharp decrease. However, in the case of SPSA containing 20 wt% MAI (MAI20), the balanced debonding was maintained at 75 °C, and its tack value hardly changed with temperature. As the MAI content increased, the peel strength at 25 °C decreased due to the microphase separation between PDMS- and acryl-blocks in SPSA, but the shear adhesion failure temperature (SAFT) increased almost linearly from 41.3 to 122.8 °C. Unlike stainless steel substrate, SPSA showed improved peel strength on a polypropylene substrate due to its low surface energy caused by PDMS block. Owing to the addition of 20 wt% silicone-urethane dimethacrylate oligomer and 200 mJ/cm2 UV irradiation dose, MAI20 showed significantly increased 90° peel strength at 25 °C (548.3 vs. 322.4 gf/25 mm for pristine MAI20). Its heat resistance under shear stress assessed by shear adhesion failure test (SAFT) exhibited raising in failure temperature to 177.3 °C when compared to non-irradiated sample.

22 June 2022 in Polymers
Verified
Journal Article
Open access
PDF file
HSHyun-su Seo
Hyun-su Seo
JBJin-Young Bae
Jin-Young Bae
KKKiok Kwon
Kiok Kwon
SSSeunghan Shin
Seunghan Shin
In this study, ionic conductive hydrogels were prepared with 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS). Acrylic acid (AA), acrylamide (AAm), and 2-hydroxyethyl acrylate (HEA) were used as comonomers to complement the adhesion properties and ion conductivity of AMPS hydrogels. Hydrogels were prepared by irradiating a 20 kGy dose of E-beam to the aqueous monomer solution. With the E-beam irradiation, the polymer chain growth and network formation simultaneously proceeded to form a three-dimensional network. The preferred reaction was determined by the type of comonomer, and the structure of the hydrogel was changed accordingly. When AA or AAm was used as a comonomer, polymer growth and crosslinking proceeded together, so a hydrogel with increased peel strength and tensile strength could be prepared. In particular, in the case of AA, it was possible to prepare a hydrogel with improved adhesion without sacrificing ionic conductivity. When the molar ratio of AA to AMPS was 3.18, the 90° peel strength of AMPS hydrogel increased from 171 to 428 gf/25 mm, and ionic conductivity slightly decreased, from 0.93 to 0.84 S/m. By copolymerisation with HEA, polymer growth was preferred compared with chain crosslinking, and a hydrogel with lower peel strength, swelling ratio, and ionic conductivity than the pristine AMPS hydrogel was obtained.