Irregularities in the geometry and flexibility of railway crossings cause large impact forces, leading to rapid degradation of crossings. Precise stress and strain analysis is essential for understanding the behavior of dynamic frictional contact and the related failures at crossings. In this research, the wear and plastic deformation because of wheel–rail impact at railway crossings was investigated using the finite-element (FE) method. The simulated dynamic response was verified through comparisons with in situ axle box acceleration (ABA) measurements. Our focus was on the contact solution, taking account not only of the dynamic contact force but also the adhesion–slip regions, shear traction, and microslip. The contact solution was then used to calculate the plastic deformation and frictional work. The results suggest that the normal and tangential contact forces on the wing rail and crossing nose are out-of-sync during the impact, and that the maximum values of both the plastic deformation and frictional work at the crossing nose occur during two-point contact stage rather than, as widely believed, at the moment of maximum normal contact force. These findings could contribute to the analysis of nonproportional loading in the materials and lead to a deeper understanding of the damage mechanisms. The model provides a tool for both damage analysis and structure optimization of crossings.

Operational modal analysis (OMA) enables the identification of modal characteristics under operational loads and conditions. Traditional frequency-domain methods cannot directly capture modal changes over time, while existing time-frequency representations are not sufficiently interpretable due to spurious modes and implicit parameter design. This paper develops a new OMA method in time-frequency representation based on frequency-domain decomposition (FDD). Short-time FDD and a convolution-based strategy are proposed to obtain singular values and local mode shape similarity, respectively, which are further fused into mode indicators by a fuzzy-based strategy mimicking the modal assurance criterion. The method provides not only a global view of the modal characteristics over time and frequency but also estimates of the modal parameters. It is applicable to strongly nonstationary responses under time-varying loads and conditions. All the parameters explicitly affect the time-frequency representation, and the interpretability is enhanced by including physical information from the user’s prior knowledge in selecting parameters and peak bands. The proposed method is validated based on a study of railway sleepers under train passage. The rigid-body motions and bending modes are identified at frequencies up to 6,500 Hz in laboratory tests and 4,500 Hz in field tests at speeds up to 200 km/h. The identified natural frequencies and mode shapes agree with experimental modal analysis (EMA). The proposed method outperforms EMA in terms of broad frequency range and low measurement cost and can be potentially applied to structural health monitoring under operational conditions.

The conventional vertical track quality index (TQI) based on the standard deviation of longitudinal levels yields standardized railway track condition assessment. Nevertheless, its capability to identify problems is limited, particularly in the ballast and substructure layers when abrupt changes affect train-track interaction. Previous research shows that dynamic responses from moving trains via axle box acceleration (ABA) measurements can quantify abrupt changes in the vertical dynamic responses. Thus, this paper proposes a framework to design an enhanced vertical TQI, called EnVTQI, by integrating track longitudinal levels and dynamic responses from ABA measurements. First, measured ABA signals are processed to mitigate the influence of variation in measurement speed. Then, substructure and ballast-related features are extracted, including scale average wavelet power (SAWP) in the ranges 0.04 m^-1 to 0.33 m^-1 (substructure) and 1.25 m^-1 to 2.50 m^-1 (ballast). This enables identifying track conditions at different track layers. Finally, EnVTQI is determined by weight averaging between the conventional vertical TQI and the ABA features from moving trains. The performance of EnVTQI is evaluated based on 48 segments of a 200-m track on a Dutch railway line. The results indicate that EnVTQI helps to distinguish track segments that cause poor train-track interaction, which the conventional TQI does not indicate. EnVTQI can supplement the conventional TQI, improving the effectiveness of track maintenance decision-making.

This study presents a measuring framework for railway transition zones using a case study on the Swedish line between Boden and Murjek. The final goal is to better understand the vertical dynamics of transition zones using hammer tests, falling weight measurements, and axle box acceleration (ABA) measurements. Frequency response functions (FRFs) from hammer tests indicate two track resonances, for which the FRF magnitudes on the plain track are at least 30% lower than those at the abutment. The falling weight measurements indicate that the track on the bridge has a much higher deflection than the track on the embankment. Two features from ABA signals, the dominant spatial frequency and the scale average wavelet power, show variation along the transition zone. These variations indicate differences in track conditions per location. Finally, the ABA features in the range of 1.05–2.86 m ⁻¹ are found to be related to the track resonance in the range of 30–60 Hz. The findings in this paper provide additional support for physically interpreting train-borne measurements for monitoring transition zones.