Cottrino Sandrine

Dr. Cottrino Sandrine

orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 December 2006 in Nanotechnology
Verified
Journal Article
Closed access
RBRomain Bachelet
Romain Bachelet
CSCottrino Sandrine
Cottrino Sandrine
GNG Nahélou
G Nahélou
VCV Coudert
V Coudert
ABA Boulle
A Boulle
ADA Dauger
A Dauger

4 December 2020 in Ceramics
Verified
Journal Article
Open access
PDF file
AVAlexandre Verchère
Alexandre Verchère
CSCottrino Sandrine
Cottrino Sandrine
Gilbert FantozziGilbert Fantozzi
Gilbert Fantozzi
SMShashank Mishra
Shashank Mishra
TGThomas Gaudisson
Thomas Gaudisson
SFSylvie Le Floch
Sylvie Le Floch
Sintering under pressure by means of the spark plasma sintering (SPS) technique is a common route to reduce the sintering temperature and to achieve ceramics with a fine-grained microstructure. In this work, high-density bulk TiO2 was sintered by high pressure SPS. It is shown that by applying high pressure during the SPS process (76 to 400 MPa), densification and phase transition start at lower temperature and are accelerated. Thus, it is possible to dissociate the two densification steps (anatase then rutile) and the transition phase during the sintering cycle. Regardless of the applied pressure, grain growth occurs during the final stage of the sintering process. However, twinning of the grains induced by the phase transition is enhanced under high pressure resulting in a reduction in the crystallite size.

30 April 2024 in Ceramics
Verified
Journal Article
Open access
PDF file
KPKacper Prokop
Kacper Prokop
CSCottrino Sandrine
Cottrino Sandrine
VGVincent Garnier
Vincent Garnier
Gilbert FantozziGilbert Fantozzi
Gilbert Fantozzi
YGYannick Guyot
Yannick Guyot
MGMałgorzata Elżbieta Guzik
Małgorzata Elżbieta Guzik
Our objective is to achieve a new good-quality and mechanically durable high-transparency material that, when activated by rare earth ions, can be used as laser sources, scintillators, or phosphors. The best functional transparent ceramics are formed from high-symmetry systems, mainly cubic. Considering hexagonal hydroxyapatite, which shows anisotropy, the particle size of the initial powder is extremely important and should be of the order of several tens of nanometers. In this work, transparent micro-crystalline ceramics of non-cubic Ca10(PO4)6(OH)2 calcium phosphate were fabricated via Spark Plasma Sintering (SPS) from two types of nanopowders i.e., commercially available (COM. HA) and laboratory-made (LAB. HA) via the hydrothermal (HT) protocol. Our study centered on examining how the quality of sintered bodies is affected by the following parameters: the addition of LiF sintering agent, the temperature during the SPS process, and the quality of the starting nanopowders. The phase purity, microstructure, and optical transmittance of the ceramics were investigated to determine suitable sintering conditions. The best optical ceramics were obtained from LAB. HA nanopowder with the addition of 0.25 wt.% of LiF sintered at 1000 °C and 1050 °C.

29 May 2025 in Journal of the European Ceramic Society
Verified
Journal Article
Open access
CSCottrino Sandrine
Cottrino Sandrine
TGThomas Gaudisson
Thomas Gaudisson
TDThierry Douillard
Thierry Douillard
NBNicholas Blanchard
Nicholas Blanchard
SMSylvain Meille
Sylvain Meille
SFSylvie Le Floch
Sylvie Le Floch

18 December 2025 in Ceramics
Verified
Journal Article
Open access
PDF file
KPKacper Prokop
Kacper Prokop
CSCottrino Sandrine
Cottrino Sandrine
VGVincent Garnier
Vincent Garnier
Gilbert FantozziGilbert Fantozzi
Gilbert Fantozzi
MSMilosz Siczek
Milosz Siczek
MGMałgorzata Elżbieta Guzik
Małgorzata Elżbieta Guzik
This work highlights the feasible fabrication of translucent ceramics from un-doped and Nd3+-doped BaLaLiWO6 (BLLW) and BaLaNaWO6 (BLNW) cubic tungstates using the Spark Plasma Sintering (SPS) method. Ceramics were sintered using pure-phase, homogeneous powders with submicron particle sizes, obtained via the solid-state reaction method. The present study investigated the microstructural, structural, and spectroscopic properties of both un-doped and Nd3+-doped sintered specimens. All the ceramic materials exhibited certain drawbacks that significantly contributed to their low transparency in both sample types. However, initial spectroscopic tests on sintered translucent ceramics doped with Nd3+ ions revealed promising properties, comparable to those of the powdered samples. Therefore, we believe that producing higher-quality ceramics would improve their spectroscopic properties. For that, further optimization of the manufacturing conditions is necessary.

19 April 2025 in Materials
Verified
Journal Article
Open access
PDF file
ECElodie Cabrol
Elodie Cabrol
CSCottrino Sandrine
Cottrino Sandrine
HMHocine Si Mohand
Hocine Si Mohand
Gilbert FantozziGilbert Fantozzi
Gilbert Fantozzi
This work presents a new approach for the fabrication of 316L/Al2O3 composites, based on a combination of spray granulation, radio frequency (RF) plasma spheroidization and spark plasma sintering (SPS). Initially, a suspension containing 316L and alumina powders is formulated by precisely adjusting the pH and selecting an appropriate dispersant, thereby ensuring homogeneous dispersion of the constituents. The spray granulation process then produces granules with controlled size and morphology. RF plasma spheroidization, carried out using a TekSphero-40 system, is investigated by varying parameters such as the power, gas flow rates, injection position and feed rate, in order to optimize the formation of spherical and dense particles. The analysis reveals a marked sensitivity to heat transfer from the plasma to the particles, with a tendency for fine particles to segregate, which underscores the necessity for precise control of the processing conditions. Finally, SPS densification, performed under a constant pressure and a rigorously controlled thermal cycle, yields composites with excellent density and hardness characteristics. This study thus demonstrates that the proposed hybrid process offers an optimal synergy between a uniform distribution of alumina and a controlled microstructure, opening up promising avenues for the design of high-performance composite materials for demanding applications.