Ademir Angelo Castro Filho

Mr. Ademir Angelo Castro Filho

Universidade Federal do Pará
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 January 2019 in Materials
Verified
Journal Article
Open access
PDF file
RRRAFAEL RIBEIRO
RAFAEL RIBEIRO
PAPaulo D. C. Assunção
Paulo D. C. Assunção
ESEmanuel B. F. Dos Santos
Emanuel B. F. Dos Santos
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
EBEduardo M. Braga
Eduardo M. Braga
AGAdrian Gerlich
Adrian Gerlich
Narrow gap welding is a prevalent technique used to decrease the volume of molten metal and heat required to fill a joint. Consequently, deleterious effects such as distortion and residual stresses may be reduced. One of the fields where narrow groove welding is most employed is pipeline welding where misalignment, productivity and mechanical properties are critical to a successful final assemblage of pipes. This work reports the feasibility of joining pipe sections with 4 mm-wide narrow gaps machined from API X80 linepipe using cold wire gas metal arc welding. Joints were manufactured using the standard gas metal arc welding and the cold wire gas metal arc welding processes, where high speed imaging, and voltage and current monitoring were used to study the arc dynamic features. Standard metallographic procedures were used to study sidewall penetration, and the evolution of the heat affected zone during welding. It was found that cold wire injection stabilizes the arc wandering, decreasing sidewall penetration while almost doubling deposition. However, this also decreases penetration, and incomplete penetration was found in the cold wire specimens as a drawback. However, adjusting the groove geometry or changing the welding parameters would resolve this penetration issue.

1 February 2019 in Diamond and Related Materials
Verified
Journal Article
Closed access
CLCristhian Ricardo Loayza Loayza
Cristhian Ricardo Loayza Loayza
DBDiego Jorge Alves Borges
Diego Jorge Alves Borges
DCDanyella C.S. Cardoso
Danyella C.S. Cardoso
PAPaulo D.C. Assunção
Paulo D.C. Assunção
VFVictor O. Ferreira
Victor O. Ferreira
EBEduardo M. Braga
Eduardo M. Braga

21 October 2020 in Scientific Reports
Verified
Journal Article
Open access
PDF file
DBDiego Jorge Alves Borges
Diego Jorge Alves Borges
DCD. C. S. Cardoso
D. C. S. Cardoso
EBE. M. Braga
E. M. Braga
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
MRM. A. L. Dos Reis
M. A. L. Dos Reis
CLC. R. L. Loayza
C. R. L. Loayza
This paper aims to establish the most indicated route to manufacture a nanostructured powder composed of 5 wt% Multi-walled Carbon Nanotubes and 304LSS powder. Four specimens were prepared using Mechanical Alloying and Chemical Treatment (CT) with Hydrogen Peroxide ( $${\mathrm{H}}_{2}{\mathrm{O}}_{2}$$H2O2 ) as the main processes. A thermal treatment post-processing was used in half of the samples to remove the remaining amorphous carbon and to evaluate its effects. Regarding the powder analysis, attachment, amorphous carbon degree, crystallinity, and doping of the CNT throughout the metal matrix were investigated. The nanostructured powders were then inserted as a core in a 304LSS tubular rod to perform the arc welding process. The CT route eliminated the amorphous carbon and generated more refiner grains, which provided a cross-section hardness gain of more than 40% regarding the 304LSS joint. In summary, the CT route, combined with the GTAW process, provided a new method for nanocomposite manufacturing by combining shorter preparation steps, obtaining an improvement in the microstructural and hardness performance.

30 August 2018 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
TCTárcio dos Santos Cabral
Tárcio dos Santos Cabral
SDSileno Espíndula Dias
Sileno Espíndula Dias
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
PBPaola Evelen Costa Baia
Paola Evelen Costa Baia
DBDiego Jorge Alves Borges
Diego Jorge Alves Borges
EBEduardo de Magalhães Braga
Eduardo de Magalhães Braga

1 January 2025 in Journal of Mining and Metallurgy, Section B: Metallurgy
Verified
Journal Article
Open access
PDF file
CVCharles Hudson Martins de Vasconcelos
Charles Hudson Martins de Vasconcelos
LVLe Sénéchal Naiara Vieira
Le Sénéchal Naiara Vieira
CLCristhian Ricardo Loayza Loayza
Cristhian Ricardo Loayza Loayza
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
DBde Eduardo Magalhaes Braga
de Eduardo Magalhaes Braga
RWRicardo Weber
Ricardo Weber
This study investigates the effects of Gas Metal Arc Welding (GMAW) parameters?specifically welding speed and stickout? on the dilution and mechanical properties of welded joints composed of ultra-high hardness quenched and tempered (UHH-Q&T) armor steel and austenitic stainless steel filler metal. An optimization methodology was used to set constant parameters, including wire diameter, gas flow rate, welding voltage, and wire feed speed, based on equipment capabilities. Experimental trials varied welding speed and electrode stick-out while maintaining a constant current through inductance control. Although the welding parameters affected the melted base and filler metal areas, the dilution percentage remained unaffected. The correlation between dilution and welding current was validated. Microstructural and mechanical analyses confirmed the consistent behavior of the welded joints under the tested conditions.

8 October 2018 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
TCTárcio dos Santos Cabral
Tárcio dos Santos Cabral
SDSileno Espíndula Dias
Sileno Espíndula Dias
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
PBPaola Evelen Costa Baia
Paola Evelen Costa Baia
DBDiego Jorge Alves Borges
Diego Jorge Alves Borges
EBEduardo de Magalhães Braga
Eduardo de Magalhães Braga
In the original publication, the co-author’s surname has been published incorrectly as “Sileno Espíndola Dias”. The correct name should read as “Sileno Espíndula Dias”.