Eduardo de Magalhães Braga

Eduardo de Magalhães Braga

Auto-generated profile, based on publicly available information

Eduardo de Magalhães Braga

Federal University of Para - UFPA, Department of Mechanical Engineering, Belem, Brazil

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 January 2019 in Materials
Verified
Journal Article
Open access
PDF file
RRRAFAEL RIBEIRO
RAFAEL RIBEIRO
PAPaulo D. C. Assunção
Paulo D. C. Assunção
ESEmanuel B. F. Dos Santos
Emanuel B. F. Dos Santos
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
EBEduardo M. Braga
Eduardo M. Braga
AGAdrian Gerlich
Adrian Gerlich
Narrow gap welding is a prevalent technique used to decrease the volume of molten metal and heat required to fill a joint. Consequently, deleterious effects such as distortion and residual stresses may be reduced. One of the fields where narrow groove welding is most employed is pipeline welding where misalignment, productivity and mechanical properties are critical to a successful final assemblage of pipes. This work reports the feasibility of joining pipe sections with 4 mm-wide narrow gaps machined from API X80 linepipe using cold wire gas metal arc welding. Joints were manufactured using the standard gas metal arc welding and the cold wire gas metal arc welding processes, where high speed imaging, and voltage and current monitoring were used to study the arc dynamic features. Standard metallographic procedures were used to study sidewall penetration, and the evolution of the heat affected zone during welding. It was found that cold wire injection stabilizes the arc wandering, decreasing sidewall penetration while almost doubling deposition. However, this also decreases penetration, and incomplete penetration was found in the cold wire specimens as a drawback. However, adjusting the groove geometry or changing the welding parameters would resolve this penetration issue.

17 September 2024 in Metals
Verified
Journal Article
Open access
PDF file
ASAlberto Solary da Silva Silva
Alberto Solary da Silva Silva
MSMário Edson Sousa
Mário Edson Sousa
EBEduardo M. Braga
Eduardo M. Braga
Marcos Allan Leite dos ReisMarcos Allan Leite dos Reis
Marcos Allan Leite dos Reis
The demand for more efficient and sustainable electrical systems has driven research in the quest for innovative materials that enhance the properties of electrical conductors. This study investigated the influence of copper (Cu) coating and multi-walled carbon nanotubes (MWCNTs) on aluminum metal substrate through the pulsed electrodeposition technique. Parameters such as the concentration of chemical elements, current, voltage, temperature, time, and electrode spacing were optimized in search of improving the nanocomposite coating. The metallic substrate underwent anodization as surface preparation for coating. Characterization techniques employed included Field Emission Gun—Scanning Electron Microscopy (FEG-SEM) for analyzing coating morphology, Energy-Dispersive X-Ray Spectroscopy (EDS), Raman spectroscopy, and Kelvin probe for obtaining surface electrical conductivity values. Homogeneous dispersion of the Cu-MWCNTs film coating was achieved across the entire surface of the aluminum plate, creating a complex morphology. The doping effect was highlighted by changes in the vibrational characteristics of the nanocomposite, which affected the Raman spectrum dispersion bands. An increase in surface electrical conductivity by ≈52.33% compared to the control sample was obtained. Therefore, these results indicate that the improvement in the material’s electrical properties is intrinsically related to the complex morphology achieved with the adopted Cu-MWCNT nanocomposite coating process.

30 August 2018 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
TCTárcio dos Santos Cabral
Tárcio dos Santos Cabral
SDSileno Espíndula Dias
Sileno Espíndula Dias
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
PBPaola Evelen Costa Baia
Paola Evelen Costa Baia
DBDiego Jorge Alves Borges
Diego Jorge Alves Borges
EBEduardo de Magalhães Braga
Eduardo de Magalhães Braga

1 January 2025 in Journal of Mining and Metallurgy, Section B: Metallurgy
Verified
Journal Article
Open access
PDF file
CVCharles Hudson Martins de Vasconcelos
Charles Hudson Martins de Vasconcelos
LVLe Sénéchal Naiara Vieira
Le Sénéchal Naiara Vieira
CLCristhian Ricardo Loayza Loayza
Cristhian Ricardo Loayza Loayza
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
DBde Eduardo Magalhaes Braga
de Eduardo Magalhaes Braga
RWRicardo Weber
Ricardo Weber
This study investigates the effects of Gas Metal Arc Welding (GMAW) parameters?specifically welding speed and stickout? on the dilution and mechanical properties of welded joints composed of ultra-high hardness quenched and tempered (UHH-Q&T) armor steel and austenitic stainless steel filler metal. An optimization methodology was used to set constant parameters, including wire diameter, gas flow rate, welding voltage, and wire feed speed, based on equipment capabilities. Experimental trials varied welding speed and electrode stick-out while maintaining a constant current through inductance control. Although the welding parameters affected the melted base and filler metal areas, the dilution percentage remained unaffected. The correlation between dilution and welding current was validated. Microstructural and mechanical analyses confirmed the consistent behavior of the welded joints under the tested conditions.

1 January 2020 in Brazilian Journal of Development
Verified
Journal Article
Open access
PDF file
RBRenan Teixeira Baia
Renan Teixeira Baia
SLSelma Lidia Azevedo Lobato
Selma Lidia Azevedo Lobato
EMEmanuel Negrao Macedo
Emanuel Negrao Macedo
KOKleber Bittencourt Oliveira
Kleber Bittencourt Oliveira
EBEduardo Magalhães Braga
Eduardo Magalhães Braga
DEDiego Estumano
Diego Estumano
Inverse problem for estimating and optimization of parameters of batch ethanol fermentation process using Bayesian techniques / Problema inverso para estimativa e otimização de parâmetros no processo de fermentação de etanol em reator batelada usando técnicas Bayesianas

8 October 2018 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
TCTárcio dos Santos Cabral
Tárcio dos Santos Cabral
SDSileno Espíndula Dias
Sileno Espíndula Dias
AFAdemir Angelo Castro Filho
Ademir Angelo Castro Filho
PBPaola Evelen Costa Baia
Paola Evelen Costa Baia
DBDiego Jorge Alves Borges
Diego Jorge Alves Borges
EBEduardo de Magalhães Braga
Eduardo de Magalhães Braga
In the original publication, the co-author’s surname has been published incorrectly as “Sileno Espíndola Dias”. The correct name should read as “Sileno Espíndula Dias”.