Rock bursts have recently become a serious problem in the horizontal section mining of steeply inclined extra-thick coal seams (SIETCSs). However, few studies have been carried out to investigate their mechanisms and prevention. In this study, numerical simulation and field measurements were carried out to investigate the mechanism of rock bursts in the horizontal section mining of an SIETCS. A Universal Distinct Element Code (UDEC) Trigon model was built, based on the Yaojie No.3 Coal Mine, and calibrated through laboratory tests and RQD methods. The results demonstrate that the coal in the elastic zone around the roof is in a high static stress state, due to the asymmetric clamping and squeezing of the roof and floor. Strong dynamic loads are formed by breakage of the roof and the failure of multiple hinged beam structures during the evolution process of the overlying strata. Rock bursts occur on the roof side when the superimposition of the static stress ${\sigma }_s$ and stress increment ${\sigma }_d$ induced by such dynamic loads is greater than the critical stress ${\sigma }_{\min }$ of the coal and rock. We propose a technical prevention scheme for the considered mine. Field studies suggest that the proposed technology can effectively prevent and control rock bursts in the horizontal section mining of SIETCSs.

When mining-induced fractures reach overlying aquifers, water enters the mining area and the coal is under different natural water saturation conditions, which significantly affect the mechanical behavior of the coal. In this study, uniaxial compression tests were conducted on dry, partially saturated, quasi-saturated, and fully saturated coal samples. The mechanical parameters, acoustic emission (AE) activities, and failure patterns of differently saturated coal samples were analyzed. The effect of water content on the behavior of coal and suggestions to ensure safe underground coal mining were discussed. The results indicate that the water content in coal increases nonlinearly with intrusion time and can be regarded as a logarithmic function. With increasing water saturation, the mechanical strength of the coal decreases on the whole and the AE activities, crack development, and burst severity are weakened significantly. The failure pattern of the coal samples changes from a dynamic type to a quasi-static one and from a compressive-shear type to a tensile one. Water content has four main effects on the mechanical behavior of the coal samples. These are a liquid bridge force, a water softening effect, a wedge effect, and a lubrication effect. With increasing water saturation, the effect of water gradually increases and predominates the coal failure, leading to a continuous decline in the strength of the coal samples. When the coal around the mining space is subjected to water, the high degree of water saturation in the coal decreases the risks of coal bursts significantly; however, it causes a large deformation and instability of the roadways. To ensure safe mining, more measures should be taken to decrease the amount of inrushing water, reduce the stress, and reinforce the anchor bolting support.

Monitoring and early-warning are critical for the prevention and controlling of rock burst in deep coal mining. In this study, rock burst risk assessment criterion was built based on the correlativity between seismic velocity and stress state in coal and rock body. Passive seismic velocity tomography using mining-induced seismic waves was conducted regularly and continuously. The evolution of rock burst risk and range in front of a deep longwall panel with folds and adjoining goaf was determined. The influence of pressure-relief measures on rock burst risk was analyzed. The study results indicate that burst risk level and range during panel retreating increase first and then decrease, the peak is reached when it is located at 1# syncline shaft area. When approaching the crossheading, high burst risk zones distribute along the crossheading and further intersect with those in 1# syncline shaft area. Burst risk zones in the inclination of panel show distinct zoning features. Tomography results are in good agreement with the drilling bit result, rock burst occurrence, microseismic activity, and working resistance of hydraulic supports. Pressure-relief measures and mining layout have a distinct influence on burst risk of longwall panel. For prevention and controlling of rock burst risk in deep coal mining, pressure-relief measures should be optimized based on passive tomography results.

This research is aimed at investigating the influence of the coal height ratio on the mechanical properties and damage behavior of rock-coal-rock combined samples (RCRCS) under coupled static and dynamic loads. For this purpose, a uniaxial cyclic dynamic loading experiment with four different coal height ratios of RCRCS was conducted. Mechanical properties, failure modes, and wave velocity evolution of RCRCS were analyzed; the process of rock burst under coupled static and dynamic loads in rock-coal-rock combined structure was discussed. The following research results are obtained. (1) The peak strength of RCRCS under static and dynamic load decreases with the increasing coal height ratio as an inverse proportional function. (2) The loading and unloading modulus remains consistent for the same levels of dynamic load; the coal height ratio of 40% may be the limit for the stable value of modulus. (3) The increase of the coal height in RCRCS leads to a gradual increase of the energy release rate; the cracks develop preferentially in coal and then extend to rock sample. The distribution of AE events and damage is consistent with the distribution of passive wave velocity. The research results provide important scientific bases for the guidance of early warning of rock burst.