Yi Weng

Dr. Yi Weng


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2015 in Optics Express
Verified
Journal Article
Closed access
PDF file
YWYi Weng
Yi Weng
EIEzra Ip
Ezra Ip
Zhongqi PanZhongqi Pan
Zhongqi Pan
TWTing Wang
Ting Wang
Recently there is a growing interest in developing few-mode fiber (FMF) based distributed sensors, which can attain higher spatial resolution and sensitivity compared with the conventional single-mode approaches. However, current techniques require two lightwaves injected into both ends of FMF, resulting in their complicated setup and high cost, which causes a big issue for geotechnical and petroleum applications. In this paper, we present a single-end FMF-based distributed sensing system that allows simultaneous temperature and strain measurement by Brillouin optical time-domain reflectometry (BOTDR) and heterodyne detection. Theoretical analysis and experimental assessment of multi-parameter discriminative measurement techniques applied to distributed FMF sensors are presented. Experimental results confirm that FM-BOTDR has similar performance with two-end methods such as FM-BOTDA, but with simpler setup and lower cost. The temperature-induced expansion strain (TIES) in response to different modes is discussed as well. Furthermore, we optimized the FMF design by exploiting modal profile and doping concentration, which indicates up to fivefold enhancement in measurement accuracy. This novel distributed FM-sensing system endows with good sensitivity characteristics and can prevent catastrophic failure in many applications.

30 August 2016 in Sensors
Verified
Journal Article
Open access
PDF file
YWYi Weng
Yi Weng
EIEzra Ip
Ezra Ip
Zhongqi PanZhongqi Pan
Zhongqi Pan
TWTing Wang
Ting Wang
The concepts of spatial-division multiplexing (SDM) technology were first proposed in the telecommunications industry as an indispensable solution to reduce the cost-per-bit of optical fiber transmission. Recently, such spatial channels and modes have been applied in optical sensing applications where the returned echo is analyzed for the collection of essential environmental information. The key advantages of implementing SDM techniques in optical measurement systems include the multi-parameter discriminative capability and accuracy improvement. In this paper, to help readers without a telecommunication background better understand how the SDM-based sensing systems can be incorporated, the crucial components of SDM techniques, such as laser beam shaping, mode generation and conversion, multimode or multicore elements using special fibers and multiplexers are introduced, along with the recent developments in SDM amplifiers, opto-electronic sources and detection units of sensing systems. The examples of SDM-based sensing systems not only include Brillouin optical time-domain reflectometry or Brillouin optical time-domain analysis (BOTDR/BOTDA) using few-mode fibers (FMF) and the multicore fiber (MCF) based integrated fiber Bragg grating (FBG) sensors, but also involve the widely used components with their whole information used in the full multimode constructions, such as the whispering gallery modes for fiber profiling and chemical species measurements, the screw/twisted modes for examining water quality, as well as the optical beam shaping to improve cantilever deflection measurements. Besides, the various applications of SDM sensors, the cost efficiency issue, as well as how these complex mode multiplexing techniques might improve the standard fiber-optic sensor approaches using single-mode fibers (SMF) and photonic crystal fibers (PCF) have also been summarized. Finally, we conclude with a prospective outlook for the opportunities and challenges of SDM technologies in optical sensing industry.

15 September 2014 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
XHXuan He
Xuan He
YWYi Weng
Yi Weng
Zhongqi PanZhongqi Pan
Zhongqi Pan
Space-division multiplexing using few-mode fibers (FMF) has emerged as a promising technology to overcome the next capacity crunch. The key challenges of FMF systems are inter-modal crosstalk due to random mode coupling and large differential mode group delay (DMGD). Adaptive frequency domain least mean square (FD-LMS) algorithm has been proposed as the most hardware efficient multi-input multi-output equalization method for compensating large DMGD. Except for hardware complexity, the convergence speed of the adaptive FD-LMS algorithm is another important consideration. In this paper, we propose a noise power spectral density (PSD) directed adaptive FD-LMS algorithm, which adopts variable step size to render the posterior error of each frequency bin convergent to the background noise in an additive white Gaussian noise (AWGN) channel. In a 3000 km six-mode transmission system with 35 ps/km DMGD, compared with signal PSD dependent FD-LMS method and conventional FD-LMS method, our new algorithm could improve the convergence speed by 36.1% and 48.3%, but their hardware complexity will only increase 10.7% and 17.2%, respectively.

17 May 2017 in Optical Materials Express
Verified
Journal Article
Closed access
PDF file
YWYi Weng
Yi Weng
TWTing Wang
Ting Wang
Zhongqi PanZhongqi Pan
Zhongqi Pan
There is an upward trend in applying the spatial division multiplexing (SDM) technologies from the telecom field towards multi-functional optical sensing applications attributable to enhanced spatial sensitivity and multi-parameter discriminative proficiency. In addition to our preliminary experimental demonstrations, in this paper we analytically evaluated the performance of few-mode Brillouin sensors via diverse refractive index profiles and dopant material compositions. Our results show five to ten folder improvements on the measurement accuracy associated with the intermodal differential Brillouin frequency shifts, which would be of great importance for sensing in sophisticated target environments. This work pave the way for next-generation mode division multiplexed sensing system design and corresponding high nonlinearity specialty fiber fabrication for structure health monitoring as well as oil and gas pipeline monitoring.