Arturo Macchi

Prof. Arturo Macchi

University of Ottawa, Ottawa, ON, Canada
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 December 2019 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Closed access
BDBrendon J. Doyle
Brendon J. Doyle
BGBernhard Gutmann
Bernhard Gutmann
MBMichael Bittel
Michael Bittel
THThierry Hubler
Thierry Hubler
AMArturo Macchi
Arturo Macchi
DRDominique M. Roberge
Dominique M. Roberge

5 February 2011 in Chemical Engineering Science
Verified
Journal Article
Closed access
ADA.A. Donaldson
A.A. Donaldson
AMArturo Macchi
Arturo Macchi
DKD.M. Kirpalani
D.M. Kirpalani

15 July 2016 in Journal of Flow Chemistry
Verified
Journal Article
Open access
EMEric Mielke
Eric Mielke
DRDominique M. Roberge
Dominique M. Roberge
AMArturo Macchi
Arturo Macchi
Based on previous work studying complex microreactors, it was desired to further improve the mixing efficiency by varying the mixing unit design for fast liquid-liquid reactions. Different flow regimes were studied, including slug flow, parallel flow, and drop flow. The two-phase hydrolysis of 4-nitrophenyl acetate in sodium hydroxide solution was used to evaluate the overall volumetric mass transfer coefficients (K org a) as a function of the average rate of energy dissipation (ε) for each microreactor design and all flow regimes. The liquid-liquid systems investigated used n-butanol or toluene as the organic phase solvent and a 0.5-M NaOH aqueous solution. The use of surfactant was also investigated with the toluene- water system. All microreactor geometry designs were based on contraction–expansion repeating units with asymmetric obstacles to aid the breakup of slugs and desynchronize the recombination of split streams. The investigated designs were chosen to avoid the formation of the parallel flow regime, contrary to curvature-based mixing-unit designs. The microreactor design can then be optimized to reduce the ε required to reach drop flow, since K org a has been found to be constant at equal ε for a given solvent system in this flow regime, regardless of the reactor selection. Additionally, the “3/7th” scaleup rule was applied and confirmed with the LL-Triangle mixer. It was found that, for low interfacial-tension systems (i.e., n-butanol-water), the onset of drop flow occurred at a lower ε for the LL-Triangle mixer when compared with the Sickle or LL-Rhombus mixers.

5 September 2017 in Reaction Chemistry & Engineering
Verified
Journal Article
Closed access
PDF file
EMEric Mielke
Eric Mielke
PPPatrick Plouffe
Patrick Plouffe
NKNikhil Koushik
Nikhil Koushik
MEMarkus Eyholzer
Markus Eyholzer
MGMichael Gottsponer
Michael Gottsponer
DRDominique M. Roberge
Dominique M. Roberge
Non-reactive and reactive heat transfer experiments were performed in the FlowPlate® system manufactured by Ehrfeld Mikrotechnik, which is composed of alternating reactor and heat transfer fluid plates within a rack. The non-reactive model system studied a rectangular serpentine channel with Reynolds numbers ranging from 400–2000, and a Gnielinski-type model was fit to the internal Nusselt number. A silver-based thermal paste was shown to reduce the external resistance to heat transfer between the reactor and heat transfer fluid plates by ∼70%, leading to overall heat transfer coefficients of ∼2200 W m−2 K−1. In the reactive system, the synthesis of methyl 2-oxobutanoate, using dimethyl-oxalate and the Grignard reagent ethylmagnesium chloride, was highlighted as a test reaction to differentiate localized heat transfer characteristics across different reactors. The Grignard reaction was used to compare the impact of various micro-mixer geometries, materials, injection ports, and scales on hotspot formation in the reactors. Finally, an analysis of four case studies that can be extended to any micro-reactor system with known overall heat transfer coefficients was presented using the fourth Damköhler number to determine a maximum channel diameter that would remove energy sufficiently quick to avoid hotspot formation.

24 May 2016 in Energy Technology
Verified
Journal Article
Open access
PDF file
BDBenoit Duhoux
Benoit Duhoux
PMPoupak Mehrani
Poupak Mehrani
DLDennis Y. Lu
Dennis Y. Lu
RSRobert T. Symonds
Robert T. Symonds
Edward AnthonyEdward Anthony
Edward Anthony
AMArturo Macchi
Arturo Macchi
In this work, a combined calcium looping and chemical looping combustion (CaL–CLC) technology is simulated at thermodynamic equilibrium conditions and the results in terms of efficiency, power production, and solids circulation rates are compared with the case of using CaL alone. In addition, a new solids looping configuration in the CaL–CLC process is proposed with the purpose of mitigating the loss of calcium oxide conversion after high cycle numbers. Simulations show an improved process efficiency of the CaL–CLC method compared with CaL alone (34.2 vs. 31.2 % higher heat value) and an increased power output (136 vs. 110 MWe additional power) due to the higher energy requirement to preheat the reactants. A sensitivity analysis of the process operating parameters highlights the particular importance of the temperature difference between reactors, which has a strong impact on the required mass of solids circulating in the loops. Finally, partial carbon dioxide capture scenarios are considered and indicate that lower capture levels are suitable to match regulation targets.

31 May 2019 in The Canadian Journal of Chemical Engineering
Verified
Journal Article
Closed access
PDF file
AMArturo Macchi
Arturo Macchi
PPPatrick Plouffe
Patrick Plouffe
Gregory Scott PatienceGregory Scott Patience
Gregory Scott Patience
DRDominique M. Roberge
Dominique M. Roberge