This paper proposes a novel linear-rotary permanent-magnet actuator (LRPMA) with interlaced poles, which has the merit of using only 50% of the neodymium-iron-boron permanent magnets when compared with those used in traditional Halbach structure. By assuming the stator is slotless, the magnetic field distribution of the LRPMA is initially analyzed using the magnetic scalar potential in the Cartesian coordinate system. A method for calculating the relative permeance by Schwarz-Christoffel transformation (SCT) is subsequently deduced to analyze the magnetic field in detail and predict the cogging force/torque of LRPMA very accurately. The analytical linear cogging force and rotary cogging torque are derived and verified for the design optimization of the actuator. The 3-D finite-element method is used to verify the correctness and effectiveness of the proposed SCT.
14 June 2021 in IEEE Transactions on Applied Superconductivity
A linear-rotary motion permanent magnet (PM) generator is investigated with six axial modular E-shaped stator sections arranged circumferentially, which can meet the requirement of wave and tidal energies generation. The PM pole is magnetized in radial direction, and the adjacent PM poles with opposite magnetized directions are interlaced by half mover pole pitch both in circumferential and axial directions, which are located on the mover surface. The rotational and rectilinear motions are achieved by one magnetic circuit structure according to the transverse flux principle and electromagnetic induction principle. The optimization design and electromagnetic properties of the proposed motor are calculated by 3-D finite element simulation. Then the optimal structural parameters are obtained. The back electromotive force (back EMF) and harmonics, the amplitudes of the cogging torque and detent force are decreased than those of the initial topology. Since three phases of the nine phase windings generate same initial phase angle of back EMF whether it works in rotational or rectilinear motion, the traditional three phase energy storage system can be used to realize the energy storage of the nine phase windings, which reduces the difficulty of electrical energy storage. The variation of the amplitude of back EMF is hardly affected with different mover positions, which is conducive to improve the efficiency of marine energy power generation.
24 December 2018 in IEEE Transactions on Applied Superconductivity
Flux reversal linear rotary permanent magnet actuator (FR-LRPMA) is a two-degree-of-freedom actuator with two ferro-magnetic (Fe) poles and two permanent magnet (PM) poles mounted on the surface of each stator pole. The flux linkage waveform of the actuator is more sinusoidal than that of the tra-ditional topology, which are analyzed by the ideal linear model of one stator section of the proposed actuator. In order to reduce the amplitudes of the cogging torque and detent force, a key space gap parameter of FR-LRPMA between the Fe pole and PM pole is studied in the circumferential and axial directions. The expres-sions of cogging torque and detent force are derived by the mag-netomotive force analytical method, which are used to obtain the optimal space gap parameter value. The electromagnetic charac-teristics of the actuator are analyzed by the finite element method. The amplitudes of cogging torque and detent force are reduced and the back electromotive force waveform is more sinusoidal than that of the original topology, which are verified by the experiment.
This paper develops a 3-D analytical model to compute the no-load magnetic-field distribution in a flux reversal linear-rotary permanent-magnet actuator (FR-LRPMA) with two permanent-magnet (PM) poles (PM_pole) and two ferromagnetic poles (Fe_pole) on each stator tooth. Laplace's and Poisson's equations are built assuming that the stator and the rotor are slotless and both the permeances of Fe_pole and PM_pole are the same. The tubular mover is transferred into a planar one using a curvature factor. Then a 2-D model and 3-D model for calculating the air-gap relative permeances are proposed considering the effect of slot and the permeance difference of Fe_pole and PM_pole, respectively. The expressions of 3-D magnetic flux density, cogging force, and cogging torque of the FR-LRPMA are subsequently derived and verified using the finite-element method.
The circumferential and axial widths of permanent magnet (PM) pole and E-shape stator pole of linear rotary motor with interlaced PM poles are very influential to the back electromotive force (EMF) and the flux leakage analysis is complex, which causes difficulty in optimization of the motor structure. One of the key issues in optimization design is to calculate the flux leakage accurately. In this article, the main flux and side flux variation laws of stator pole are derived by analytical method. The flux leakage can be divided into the flux leakage between the PM and the mover, flux leakage on the stator tooth tip, and the flux leakage between the adjacent PM poles and stator pole. The 3-D flux leakage calculation model is built, which is suitable for the calculation of magnetic flux based on different motor operating principles. Then the rotational and rectilinear back EMFs are calculated by analytical method, which are consistent with the results analyzed by 3-D finite element method.
8 December 2023 in IEEE Transactions on Industrial Electronics
In order to improve the drilling efficiency and accuracy of drilling robot, a linear rotary drilling motor (LRDM) is proposed with U-type stator and toroidal winding structure. The stator sections are staggered, which can use the motor space effectively. The asymmetric air gap flux density (AGFD) phenomenon of LRDM is found based on the initial magnetic field analysis by finite-element method (FEM). According to flux tube principle, the variation law of the amplitude of the asymmetric AGFD of the LRDM is derived, which can be used to realize the optimization design with less computation time. The cogging torque, detent force, torque, and thrust are taken as the optimization objectives, and the optimal values of the structure and electromagnetic parameters are obtained. Then a prototype is manufactured. The electromagnetic characteristics of the proposed motor are analyzed and verified by FEM and experimental test.