Ball bearings are commonly used in inverter driven electrical machines, where they bluecan be subject to high frequency common mode currents which accelerate their degradation. This paper investigates the impact of shaft speed, voltage amplitude and frequency on the bearing impedance, including during electrical discharges, with the aim to provide an experimentally validated approach to model their high frequency behaviour as function of operating conditions. This analysis can help the development of improved models to predict bearing currents in electric drives. A dedicated experimental setup, completely isolated from ground, is presented. It proposes dielectric plate and bolts to insulate the bearing from the support (which is connected to the ground), a dielectric coupling to insulate the dyno from bearing, dielectric sheets to insulate the brush holder from the ground. Different voltage and frequency amplitudes are applied between the inner and outer bearing raceways for several shaft speeds. The measured impedance amplitude and phase, currents and voltages are presented. Due to the large amount of data, a statistical approach is proposed for studying the bearings behaviour. A simple analytical bearing model is presented in order to provide an interpretation of the experimental measurements. The analysis shows that the voltage amplitude and frequency have a significant impact on electrical discharge in ball bearings, especially for certain shaft speeds strongly affecting the impedance amplitude and phase during the breakdown state.
Ball bearings are largely used in electrical machines, where the high frequency common mode currents affect their lifetime. This document presents a novel Zig-Zag stator slot opening geometry to reduce the winding-to-rotor capacitance Cwr with the consequent reduction of Bearing Voltage Ratio and electrical discharge machining bearing currents. An improved analytical model to permit the calculation of Cwr for unusual slot opening geometries is implemented. Electrostatic and electromagnetic Finite Element Analysis comparisons between the Zig-Zag, oblique and original (classical slot opening configuration) machines are performed. These comparisons suggest that the Zig-Zag model presents the best performance in terms of Bearing Voltage Ratio reduction, while keeping torque performance close to the original machine. An additional comparison between the novel Zig-Zag model and the classical one with reduced slot opening to have the same Cwr values is proposed, showing an higher degradation in terms of torque performance for the latter. The study shows that the Zig-Zag model could be a good candidate to reduce effectively electrical machine bearing currents. A validation test is proposed on two motorette prototypes having classical and Zig-Zag slot opening configurations, respectively. Moreover, the improved analytical method can be helpful for engineers and researchers to calculate Cwr with a good accuracy for unusual slot opening geometries.
23 June 2025 in IEEE Transactions on Industry Applications
The feasibility of utilizing multiphase machines in electrical vehicles (EVs) is investigated in this paper by designing three-phase, five-phase, six-phase, and nine-phase interior permanent magnet synchronous machines (IPMSMs) with the same sizing parameters as the Tesla Model 3 IPMSM which is used as a reference. The optimized three-phase machine results in a 20% higher average output torque per permanent magnet (PM) volume compared to the reference design. Multiphase machines show 3-5% higher torque per PM volume over their three-phase counterpart while achieving inherently low torque ripples. The torque-speed analysis of the multiphase machines demonstrates enhanced efficiency regions attributable to the increased output power although this improvement is accompanied by increased iron losses due to high winding factors of harmonics. PWM losses are calculated, and thermal simulations of the machines are performed to validate that the designs work with thermal limitations. It is also shown that the DC-link capacitor size can be reduced by up to 55% compared to a three-phase system by using a multiphase structure. The total number of power switches used in the drive remains the same for the six-phase machine since the lower phase currents can be achieved by increasing the number of phases. The cost analysis for each of the machines has shown that multiphase machines are not necessarily more expensive than three-phase machines since the same total number of switches considering paralleled switches in three-phase machine can be used in six-phase machine while having smaller DC-link capacitors and PM volume. As a result, 14.2% higher output power per cost can be achieved compared to the reference design.
11 September 2025 in IEEE Transactions on Transportation Electrification
Bar conductor windings with rectangular cross sections are increasingly used in electrical vehicle traction applications for their high slot fill factor, reduced losses, improved heat transfer, and manufacturing repeatability. However, ac losses from eddy currents due to skin and proximity effects limit their performance at high frequencies. This article proposes a hybrid winding design to reduce ac losses in electrical machines with bar conductors. The design integrates copper conductors with outer layers of low-conductivity materials, such as aluminum or brass, to leverage the low dc resistance of copper and mitigate ac losses caused by skin and proximity effects at high frequencies. A comprehensive analytical model and finite element analysis (FEA) are developed to optimize and validate the design, supported by experimental results from brasscopper hybrid conductors. The proposed design reduces winding losses without altering the original winding layout, providing a practical and efficient solution for enhancing the performance of traction machines.
26 July 2023 in Journal of Magnetism and Magnetic Materials
This article proposes two novel hybrid magnet rotor topologies, spoke-V and spoke-delta, for interior permanent magnet synchronous machines (IPMSMs) for reducing rare-Earth magnet usage while maintaining high electromagnetic performance in electric vehicles (EVs). Using the Tesla model 3 IPMSM as a reference, the models are parametrized and multiobjective optimization is performed. The proposed spoke-V and spoke-delta configurations achieve NdFeB volume reductions of 19.4% and 25.8%, respectively, while matching the torque performance of the reference machine. This results in a 20.5% and 35.1% improvement in torque per unit volume of rare-Earth material. Detailed electromagnetic analyses are conducted under open-circuit, peak-load, and torque-speed characteristic analysis under full operating conditions, demonstrating the feasibility of the proposed topologies for high-speed EV applications. A small-scale prototype is manufactured and tested to verify the accuracy of the calculations. These findings highlight the potential of asymmetric hybrid magnet rotor designs to deliver less rare-Earth and high-performance IPMSMs, contributing to the development of more sustainable and cost-effective electric drive solutions.