Huayong Zhao

Dr. Huayong Zhao

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 February 2014 in Energy & Fuels
Verified
Journal Article
Open access
HZHuayong Zhao
Huayong Zhao
RSRichard Stone
Richard Stone
BWBen Williams
Ben Williams
A new optical diagnostic technique has been used to measure the spatially distributed temperatures, soot diameters, and soot volume fractions in several different ethylene laminar diffusion flames to investigate the effect of adding hydrogen and helium on the soot formation. The test results show that adding hydrogen increases the flame temperature in all regions, while adding helium does not significantly affect the flame temperature in the reaction region but does increase the flame temperature elsewhere. The flame heights when adding helium and hydrogen can be calculated using the correlation introduced by Roper if the ethylene diffusion coefficient is used. This indicates that the flame height is determined by the diffusion of ethylene molecules when the hydrogen fraction is below 20%. It was also found that either adding helium or hydrogen does not significantly affect the soot diameter but does reduce the soot volume fraction. A total of 20% of helium addition by volume was measured to reduce the total soot number by 19%, while a total of 20% of hydrogen addition reduced the total soot number by 23%. In comparison, replacing the hydrocarbon with hydrogen is much more effective in reducing soot formation. Replacement of 25% ethylene by hydrogen was measured to reduce the total soot number by 66%. Apart from demonstrating the influence of hydrogen and helium on ethylene diffusion flames, these measurements provide additional data for modelers of diffusion flames, especially those with an interest in the formation of particulate matter.

1 March 2023 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
HZHuayong Zhao
Huayong Zhao
FNFrançois Nadal
François Nadal
A general mixed kinetic-diffusion boundary condition is formulated to account for the out-of-equilibrium kinetics in the Knudsen layer. The mixed boundary condition is used to investigate the problem of quasi-steady evaporation of a droplet in an infinite domain containing inert gases. The widely adopted local thermodynamic equilibrium assumption is found to be the limiting case of infinitely large kinetic Péclet number ${{Pe}_k}$ , and it introduces significant error for ${{Pe}_k} \leqslant O(10)$ , which corresponds to a typical droplet radius $a$ of a few micrometres or smaller. When compared with experimental data, solutions based on the mixed boundary condition, which take into account the temperature jump across the Knudsen layer, better predict the time evolution of $a$ than the classical $D^2$ -law (i.e. $a^2 \propto t$ , where $t$ denotes time). In the slow evaporation limit, an analytical solution is obtained by linearising the full formulation about the equilibrium condition, which shows that the $D^2$ -law can be recovered only in the large ${{Pe}_k}$ limit. For small ${{Pe}_k}$ , where the process is dominated by kinetics, a linear relation, i.e. $a \propto t$ , emerges. When the gas phase density approaches the liquid density (e.g. at high-pressure or low-temperature conditions), the increase in the chemical potential of the liquid phase due to the presence of inert gases needs to be accounted for when formulating the mixed boundary condition, an effect largely ignored in the literature so far.

22 August 2019 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
NRN. Rebelo
N. Rebelo
HZHuayong Zhao
Huayong Zhao
FNF. Nadal
F. Nadal
CGC. Garner
C. Garner
AWA. Williams
A. Williams

2 May 2024 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
HZHuayong Zhao
Huayong Zhao
RPR. Poole
R. Poole
ZZZ. Zhou
Z. Zhou

15 July 2025 in Applied Thermal Engineering
Verified
Journal Article
Closed access
XLXiang-Wei Lin
Xiang-Wei Lin
LXLin-Feng Xiang
Lin-Feng Xiang
ZZZhi-Fu Zhou
Zhi-Fu Zhou
HZHuayong Zhao
Huayong Zhao

24 April 2017 in Journal of Fluids Engineering
Verified
Journal Article
Open access
PDF file
SMStephan Mohr
Stephan Mohr
HCHenry Clarke
Henry Clarke
CGColin Garner
Colin Garner
NRNeville Rebelo
Neville Rebelo
AWAndrew M. Williams
Andrew M. Williams
HZHuayong Zhao
Huayong Zhao
Flow coefficients of intake valves and port combinations were determined experimentally for a compressed nitrogen engine under steady-state and dynamic flow conditions for inlet pressures up to 3.2 MPa. Variable valve timing was combined with an indexed parked piston cylinder unit for testing valve flows at different cylinder volumes while maintaining realistic in-cylinder transient pressure profiles by simply using a fixed area outlet orifice. A one-dimensional modeling approach describing three-dimensional valve flow characteristics has been developed by the use of variable flow coefficients that take into account the propagation of flow jets and their boundaries as a function of downstream/upstream pressure ratios. The results obtained for the dynamic flow cases were compared with steady-state results for the cylinder to inlet port pressure ratios ranges from 0.18 to 0.83. The deviation of flow coefficients for both cases is discussed using pulsatile flow theory. The key findings include the followings: (1) for a given valve lift, the steady-state flow coefficients fall by up to 21% with increasing cylinder/manifold pressure ratios within the measured range given above and (2) transient flow coefficients deviated from those measured for the steady-state flow as the valve lift increases beyond a critical value of approximately 0.5 mm. The deviation can be due to the insufficient time of the development of steady-state boundary layers, which can be quantified by the instantaneous Womersley number defined by using the transient hydraulic diameter. We show that it is possible to predict deviations of the transient valve flow from the steady-state measurements alone.