The viscosity and tribological behavior of nanofluids formed by dispersed nano-diamond particles within Poly-Alpha-Olefin (PAO6) lubricant is studied at different concentrations. The variation of coefficient of friction with nanoparticle concentration is measured using pin-on-disc tribometry under boundary, mixed, and hydrodynamic regimes of lubrication. A multi-scale multi-physics thermo-mixed lubrication model is developed to provide fundamental understanding of the measured tribometric results. The analytical approach combines continuum contact mechanics, thermal-mixed lubrication comprising the interaction of rough surfaces, as well as a thermal network heat transfer model. In particular, Einstein’s viscosity model for dispersed hard particles together with Vogel’s viscosity-temperature dependence model for fluid viscosity containing nanoparticles represent new contributions to knowledge. This integrated numerical-experimental study of nanofluid thermal and tribological assessment has not hitherto been reported in literature. It is shown that improved heat transfer capability of nanofluids is particularly effective in the reduction of friction under a mixed regime of lubrication.
Using high charge dilution low temperature combustion (LTC) strategies in a diesel engine offers low emissions of nitrogen oxides (NOx). These strategies are limited to part-load conditions and involve high levels of charge dilution, typically achieved through the use of recirculated exhaust gases (EGR). The slow response of the gas handling system, compared to load demand and fuelling, can lead to conditions where dilution levels are higher or lower than expected, impacting emissions and combustion stability. This article reports on the sensitivity of high-dilution LTC to variations in EGR rate and fuel injection timing. Impacts on engine efficiency, combustion stability and emissions are assessed in a single-cylinder engine and compared to in-cylinder flame temperatures measured using a borescope-based two-colour pyrometer. The work focuses on low-load conditions (300 kPa gross indicated mean effective pressure) and includes an EGR sweep from conventional diesel mode to high-dilution LTC, and sensitivity studies investigating the effects of variations in charge dilution and fuel injection timing at the high-dilution LTC condition. Key findings from the study include that the peak flame temperature decreased from ~2580 K in conventional diesel combustion with no EGR to 1800 K in LTC with low-NOx, low-soot operation and an EGR rate of 57%. Increasing the EGR to 64% reduced flame temperatures to 1400 K but increased total hydrocarbon (THC) and carbon monoxide (CO) emissions by 30–50% and increased fuel consumption by 5–7%. Charge dilution was found to have a stronger effect on the combustion process than the diesel injection timing under these LTC conditions. Advancing fuel injection timings at increasing dilution kept combustion instability below 2.5%. Peak in-cylinder temperatures were maintained in the 2000–2100 K range, while THC and CO emissions were controlled by delaying the onset of bulk quenching. Very early injection (earlier than 24 °CA before top-dead-centre) resulted in spray impingement on the piston crown, resulting in degraded efficiency and higher emissions. The results of this study demonstrate the potential of fuel injection timing modification to accommodate variations in charge dilution rates while maintaining low NOx and PM emissions in a diesel engine using low-temperature combustion strategies at part loads.
This study presents a new flexible dynamic model for drive systems comprising lubricated bearings operating under conditions representative of electrified vehicle powertrains. The multi-physics approach importantly accounts for the tribological phenomena at the roller–race conjunction and models their effect on shaft-bearing system dynamics. This is achieved by embedding a non-linear lubricated bearing model within a flexible system level model; this is something which has not, to the authors’ knowledge, been reported on hitherto. The elastohydrodynamic (EHL) film is shown to increase contact deflection, leading to increased contact forces and total bearing stiffness as rotational speeds increase. Results show that for a 68 Nm hub motor operating up to 21,000 rpm, the input bearing EHL film reaches a thickness of 4.15 m. The lubricant entrainment increases the roller–race contact deflection, causing the contact stiffness to increase non-linearly with speed. The contribution of the lubricant film leads to a 16.6% greater bearing stiffness at 21,000 rpm when compared to conventional dry-bearing modelling methods used in current multi-body dynamic software. This new methodology leads to more accurate dynamic response of high-speed systems necessary for the next generation of electrified vehicles.
Flow coefficients of intake valves and port combinations were determined experimentally for a compressed nitrogen engine under steady-state and dynamic flow conditions for inlet pressures up to 3.2 MPa. Variable valve timing was combined with an indexed parked piston cylinder unit for testing valve flows at different cylinder volumes while maintaining realistic in-cylinder transient pressure profiles by simply using a fixed area outlet orifice. A one-dimensional modeling approach describing three-dimensional valve flow characteristics has been developed by the use of variable flow coefficients that take into account the propagation of flow jets and their boundaries as a function of downstream/upstream pressure ratios. The results obtained for the dynamic flow cases were compared with steady-state results for the cylinder to inlet port pressure ratios ranges from 0.18 to 0.83. The deviation of flow coefficients for both cases is discussed using pulsatile flow theory. The key findings include the followings: (1) for a given valve lift, the steady-state flow coefficients fall by up to 21% with increasing cylinder/manifold pressure ratios within the measured range given above and (2) transient flow coefficients deviated from those measured for the steady-state flow as the valve lift increases beyond a critical value of approximately 0.5 mm. The deviation can be due to the insufficient time of the development of steady-state boundary layers, which can be quantified by the instantaneous Womersley number defined by using the transient hydraulic diameter. We show that it is possible to predict deviations of the transient valve flow from the steady-state measurements alone.
It has been proven that performance gains in liquid nitrogen (LN2) engine systems, generating simultaneous cooling and auxiliary power, can be achieved through integration of a dedicated heat exchange fluid (HEF) circuit. The novel, HEF enhanced LN2 engine system can be utilised as an optimised hybrid solution for commercial refrigeration trucks. Although the benefits arising from HEF addition have been researched, there are no articles investigating the effect of changing the HEF composition on engine performance. This article reports a detailed experimental investigation on the performance of a novel, HEF enhanced LN2 engine system. The key contribution of the current study is the knowledge generated from investigating the impact of different HEF compositions on the engine performance under different HEF temperatures, N2 inlet conditions and engine speeds. The HEF composition was varied through changing the water content in the mixture. A thermodynamic model based on an idealised cycle was used to assist interpretation of the experimental results and assess the potential of the proposed engine architecture. The experimental study demonstrated up to 42.5% brake thermal efficiency, up to 2.67 kW of brake power and up to 174 kJ/kg specific energy, which were higher than previously published figures for LN2 engine systems. A reduction in the HEF water content was found to generally increase the engine power output at a HEF temperature of 30 °C. However, at a HEF temperature of 60 °C, the impact of HEF composition was found to be minor and nonmonotonic. The thermodynamic model predicted the upper and lower limits of the measured indicated power and indicated thermal efficiency with acceptable accuracy.