Continued human population growth has resulted in increased demand for products, including those derived from aquaculture. The main challenge in aquaculture is producing more every year. In recent years, environmentally friendly supplements that provide the necessary pathways for optimal production have been emphasized. One of them is prebiotics, selectively utilized substrates by host microorganisms conferring a health benefit. Interest in applying prebiotics in global fish farming has increased in recent years as it has been shown to improve growth, boost the immune system, resist stress conditions, and cause the modulation of digestive enzymes. These effects reflect reduced production and disease costs. However, in Latin American countries such as Mexico, large-scale use of these food supplements is needed as a sustainable alternative to improve fish production. This paper gives a review of the current advances obtained with the application of prebiotics in commercially farmed fish worldwide, mentions the prebiotics to use in the aquaculture industry, and updates the status of studies about the used prebiotics in global commercial fish cultivated in Mexico, as well as freshwater and marine endemic fish in this country. Also, the limitations of prebiotics application in terms of their use and legislation are analyzed.
This research work shows a new architecture of a novel wearable finger exoskeleton for rehabilitation; the proposed design consists of a one degree of freedom mechanism that generates the flexion and extension movement for the proximal, medial and distal phalange of the fingers to assist patients during the rehabilitation process, after neurological trauma, such as a stroke. The anatomy and anthropometric measures for the hand were used to define the design of the mechanism. In the analytic part, the representative equations for the forward and inverse kinematic analysis of the fingers are obtained, also a dynamic analysis is presented. The position and displacement continued for the structural analysis, were developed by following a static analysis, to know the deformation that the structure links show when an external load is applied in the mechanism. As result, a prototype was manufactured with acrylonitrile butadiene styrene (ABS) using an additive manufacturing machine.
Dynamic supply chains (SC) are important to reduce inventory, enable the flow of materials, maximize profits, and minimize costs. This research work presents a capacity–inventory management model via system dynamics for a dynamic supply SC, applying model-based optimal control techniques. In the context of high-volume manufacturing (HVM) that present low variability and predictable demand, for mathematical modeling purposes, a set of coupled first-order ordinary differential equations, with an analogy from the mixing problem, is presented, which relates capacity and inventory levels, taking into account a production rate at each node of interaction. The application of ordinary differential equations via the mixing problem (or compartmental analysis) is important based on the idea of a balance between the influx and outflux of raw material along the supply chain. A proper literature review on optimal control for supply chains is analyzed. The mathematical model introduced is presented in a linear time-invariant (LTI) state-space formulation. Stability analysis for the dynamic serial SC is presented, and a sensitivity analysis is also conducted for the capacity and production rate parameters considering the effects of variations in parameters along the SC. An energy-based optimal control is also developed with proper simulations.
Water contamination with pesticides is one of the major pollution problems in northwestern Mexico, and this is due to the extensive use of pesticides in agriculture. In this research, water samples of ten sampling sites (fishing grounds, beaches, and both) were analyzed in the search for 28 pesticides (organochlorines, organophosphates, pyrethroids, carbamates, among other chemical classes), supplemented with a calculation of the resulting potential environmental risk. Pesticides were separated from the matrix by liquid-liquid extraction and quantified by gas chromatography coupled to electron micro-capture (organohalogenated) and pulsed flame photometric detectors (organophosphates). In addition, the ecotoxicological risk of pesticides in algae, invertebrates, and fish was assessed, based on seawater pesticide concentrations using the Risk Quotient (RQ) and Toxic Units (TU) approach. The results showed 18 pesticides identified in the analyzed samples, where cypermethrin and chlorpyrifos were identified with the maximum concentrations of 1.223 and 0.994 μg L-1, respectively. In addition, these two pesticides have been associated with acute toxic effects on algae, invertebrates, and fish. It is important to pay particular attention to the search for long-term alternatives to the use of chlorpyrifos and cypermethrin due to their high detection rates and the risks associated with their toxic properties. However, the adoption of alternative measures to synthetic pesticide control should be a priority, moving towards sustainable practices such as the use of biopesticides, crop rotation and polycultures.
Trabajado en la elaboración de un instrumento de recopilación de datos, el cual consiste en la aplicación de un cuestionario integrado por 31 preguntas de escala tipo Likert, aplicado a 116 estudiantes. El análisis de contenido de las respuestas ha permitido analizar las actitudes y valores en los estudiantes con respecto a ecología y medio ambiente y la relación del ambiente con la ciencia y tecnología. Se concluye que se debe incluir la materia de educación ambiental en los planes de estudio de la carrera de Ingeniería Mecatrónica.
In the area of production planning and control, the aggregate production planning (APP) problem represents a great challenge for decision makers in production-inventory systems. Tradeoff between inventory-capacity is known as the APP problem. To address it, static and dynamic models have been proposed, which in general have several shortcomings. It is the premise of this paper that the main drawback of these proposals is, that they do not take into account the dynamic nature of the APP. For this reason, we propose the use of an Optimal Control (OC) formulation via the approach of energy-based and Hamiltonian-present value. The main contribution of this paper is the mathematical model which integrates a second order dynamical system coupled with a first order system, incorporating production rate, inventory level, and capacity as well with the associated cost by work force in the same formulation. Also, a novel result in relation with the Hamiltonian-present value in the OC formulation is that it reduces the inventory level compared with the pure energy based approach for APP. A set of simulations are provided which verifies the theoretical contribution of this work.