Designing a controller for autonomous vehicles capable of providing adequate performance in all driving scenarios is challenging due to the highly complex environment and inability to test the system in the wide variety of scenarios which it may encounter after deployment. However, deep learning methods have shown great promise in not only providing excellent performance for complex and non-linear control problems, but also in generalising previously learned rules to new scenarios. For these reasons, the use of deep learning for vehicle control is becoming increasingly popular. Although important advancements have been achieved in this field, these works have not been fully summarised. This paper surveys a wide range of research works reported in the literature which aim to control a vehicle through deep learning methods. Although there exists overlap between control and perception, the focus of this paper is on vehicle control, rather than the wider perception problem which includes tasks such as semantic segmentation and object detection. The paper identifies the strengths and limitations of available deep learning methods through comparative analysis and discusses the research challenges in terms of computation, architecture selection, goal specification, generalisation, verification and validation, as well as safety. Overall, this survey brings timely and topical information to a rapidly evolving field relevant to intelligent transportation systems.

An autonomous vehicle (AV) requires an accurate perception of its surrounding environment to operate reliably. The perception system of an AV, which normally employs machine learning (e.g., deep learning), transforms sensory data into semantic information that enables autonomous driving. Object detection is a fundamental function of this perception system, which has been tackled by several works, most of them using 2D detection methods. However, the 2D methods do not provide depth information, which is required for driving tasks, such as path planning, collision avoidance, and so on. Alternatively, the 3D object detection methods introduce a third dimension that reveals more detailed object's size and location information. Nonetheless, the detection accuracy of such methods needs to be improved. To the best of our knowledge, this is the first survey on 3D object detection methods used for autonomous driving applications. This paper presents an overview of 3D object detection methods and prevalently used sensors and datasets in AVs. It then discusses and categorizes the recent works based on sensors modalities into monocular, point cloud-based, and fusion methods. We then summarize the results of the surveyed works and identify the research gaps and future research directions.

For an autonomous vehicle to operate safely and effectively, an accurate and robust localization system is essential. While there are a variety of vehicle localization techniques in literature, there is a lack of effort in comparing these techniques and identifying their potentials and limitations for autonomous vehicle applications. Hence, this paper evaluates the state-of-the-art vehicle localization techniques and investigates their applicability on autonomous vehicles. The analysis starts with discussing the techniques which merely use the information obtained from on-board vehicle sensors. It is shown that although some techniques can achieve the accuracy required for autonomous driving but suffer from the high cost of the sensors and also sensor performance limitations in different driving scenarios (e.g., cornering and intersections) and different environmental conditions (e.g., darkness and snow). This paper continues the analysis with considering the techniques which benefit from off-board information obtained from V2X communication channels, in addition to vehicle sensory information. The analysis shows that augmenting off-board information to sensory information has potential to design low-cost localization systems with high accuracy and robustness, however, their performance depends on penetration rate of nearby connected vehicles or infrastructure and the quality of network service.

3D object detection is a common function within the perception system of an autonomous vehicle and outputs a list of 3D bounding boxes around objects of interest. Various 3D object detection methods have relied on fusion of different sensor modalities to overcome limitations of individual sensors. However, occlusion, limited field-of-view and low-point density of the sensor data cannot be reliably and cost-effectively addressed by multi-modal sensing from a single point of view. Alternatively, cooperative perception incorporates information from spatially diverse sensors distributed around the environment as a way to mitigate these limitations. This article proposes two schemes for cooperative 3D object detection using single modality sensors. The early fusion scheme combines point clouds from multiple spatially diverse sensing points of view before detection. In contrast, the late fusion scheme fuses the independently detected bounding boxes from multiple spatially diverse sensors. We evaluate the performance of both schemes, and their hybrid combination, using a synthetic cooperative dataset created in two complex driving scenarios, a T-junction and a roundabout. The evaluation shows that the early fusion approach outperforms late fusion by a significant margin at the cost of higher communication bandwidth. The results demonstrate that cooperative perception can recall more than 95% of the objects as opposed to 30% for single-point sensing in the most challenging scenario. To provide practical insights into the deployment of such system, we report how the number of sensors and their configuration impact the detection performance of the system.

Automated vehicles are increasingly getting main-streamed and this has pushed development of systems for autonomous manoeuvring (e.g., lane-change, merge, and overtake) to the forefront. A novel framework for situational awareness and trajectory planning to perform autonomous overtaking in high-speed structured environments (e.g., highway and motorway) is presented in this paper. A combination of a potential field like function and reachability sets of a vehicle are used to identify safe zones on a road that the vehicle can navigate towards. These safe zones are provided to a tube-based robust model predictive controller as reference to generate feasible trajectories for combined lateral and longitudinal motion of a vehicle. The strengths of the proposed framework are: 1) it is free from non-convex collision avoidance constraints; 2) it ensures feasibility of trajectory even if decelerating or accelerating while performing lateral motion; and 3) it is real-time implementable. The ability of the proposed framework to plan feasible trajectories for high-speed overtaking is validated in a high-fidelity IPG CarMaker and Simulink co-simulation environment.