Mikail Olam

Dr. Mikail Olam

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2023
Verified
Book Chapter
Open access
PDF file
MOMikail Olam
Mikail Olam
Microplastics (MPs), which have recently threatened living organisms, are widely distributed throughout the world’s fresh waters, oceans, and seas. HDPEs and PETs are produced and used in significant quantities in plastics. High-density polyethylene (HDPE) and polyethylene terephthalate (PET), which can survive in the natural environment for many years, are resistant to thermal, mechanical, and biological effects. This study examined the current developments in the sources of high-density polyethylene microplastics (mHDPE) and polyethylene terephthalate microplastics (mPET), and their disposal and properties. mHDPE and mPET microplastics consist of several sources, including their debris that breaks down their waste into smaller pieces as a result of physical and chemical processes, as well as micro-sized pieces of plastic commonly applied in personal care products or synthetic textiles. mHDPE and mPET pollution has become an important environmental problem with the potential to harm human health by entering the human and animal food chain. mHDPEs and mPETs, which enter the living organism through ingestion, inhalation, and dermal contact in general, adversely affect the cellular mechanisms in different parts of the body. In addition, they are decomposed into free radicals by the effects of external factors such as light and temperature, as well as biological agents and chemical wastes in the environment, which significantly affects the sustainability of the ecological environment.

1 January 2022 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
MOMikail Olam
Mikail Olam
NTNihat Tosun
Nihat Tosun

16 June 2023 in Biomass Conversion and Biorefinery
Verified
Journal Article
Closed access
PDF file
MOMikail Olam
Mikail Olam
FGFigen Gündüz
Figen Gündüz
HKHüseyin Karaca
Hüseyin Karaca

23 March 2022 in Environmental Progress & Sustainable Energy
Verified
Journal Article
Closed access
MOMikail Olam
Mikail Olam
HKHüseyin Karaca
Hüseyin Karaca

6 January 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
MOMikail Olam
Mikail Olam
NTNihat Tosun
Nihat Tosun

24 May 2022 in Advances in Materials and Processing Technologies
Verified
Journal Article
Closed access
MOMikail Olam
Mikail Olam
In this study, filaments for FDM 3D printers were produced by extrusion method by mixing 95% polylactic acid (PLA), 1% hydroxyapatite (HA) and 4% titanium dioxide (TiO2). The extruder temperature, raster angle and layer thickness parameters, and printing defects of the prints made with the FDM 3D printer were examined. According to the dimensional analysis, 0.5–2% dimensional deviations occurred in 3D prints. The least average roughness value was 12.1 µm on the Z-axis surface, the highest average roughness value was 14.6 µm on the Y-axis surface. The highest ultimate tensile strength was 57 MPa at the layer thickness of 0.15 mm, extruder temperature of 205°C and raster orientation of 45°. The highest modulus of elasticity was 2020 MPa at the layer thickness of 0.15 mm, extruder temperature of 220°C and raster orientation of 45°. The highest elongation at break was 2.0 mm at the layer thickness of 0.20 mm, extruder temperature of 220°C and raster orientation of 45°. The dimensional deviations in the X, Y and Z axes plane were approximately 1%. X parallelism, Y parallelism and Z profile surface values were approximately 0.6%.