Agnieszka Malec

Ms. Agnieszka Malec

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 October 2021 in Energies
Verified
Journal Article
Open access
PDF file
AMAgnieszka Malec
Agnieszka Malec
Tomasz CholewaTomasz Cholewa
Tomasz Cholewa
Alicja Siuta-OlchaAlicja Siuta-Olcha
Alicja Siuta-Olcha
Domestic hot water preparation is one of the main sources of energy consumption in households. One of the most important elements of domestic hot water (DHW) preparation installation is the storage tank. Its design can significantly affect the efficiency of the system and energy consumption for hot water preparation. This paper presents the results of an experimental study to examine seven different designs of the cold water inlet to the storage tank and the use of two types of obstacles inside this tank placed at three different heights. The number of stratification and the energy efficiency of the system for each variant were examined. Additionally, tests were carried out for different profiles of hot water consumption in order to examine the temperature changes in the DHW tank. A system with an inlet, as an elbow facing down with a single plate, turned out to be the most advantageous variant (3–8% increase in energy efficiency compared to the basic inlet variant). An analogous analysis of the use of obstacles inside the tank showed that the most optimal solution is to place the partition, which allows the water flow on the sides of the tank, in its lower parts (energy efficiency higher by up to 15% compared to the variant without a partition). These solutions showed the highest energy efficiency for DHW production and the lowest energy demand for hot water heating in the tank among all analyzed variants.

6 February 2021 in Energies
Verified
Journal Article
Open access
PDF file
Tomasz CholewaTomasz Cholewa
Tomasz Cholewa
AMAgnieszka Malec
Agnieszka Malec
Alicja Siuta-OlchaAlicja Siuta-Olcha
Alicja Siuta-Olcha
Andrzej SmolarzAndrzej Smolarz
Andrzej Smolarz
PMPiotr Muryjas
Piotr Muryjas
KŁKrystian Łygas
Krystian Łygas
Nowadays, the attention of designers and service providers is especially focused on energy efficiency and integration of renewable energy sources (RES). However, the knowledge on smart devices and automated, easily applicable algorithms for optimizing heating consumption by effectively taking advantage of solar heat gains, while avoiding overheating, is limited. This paper presents a simple method for taking into account the influence of solar heat gains in the form of solar radiation for the purposes of forecasting or controlling thermal power for heating of buildings. On the basis of field research carried out for seven buildings (five residential buildings and two public buildings) during one heating season, it was noticed that it was justified to properly narrow down the input data range included in the building energy model calculations in order to obtain a higher accuracy of calculations. In order to minimize the impact of other external factors (in particular wind speed) affecting the heat consumption for heating purposes, it was recommended to consider the data range only at wind speeds below 3 m/s. On the other hand, in order to minimize the impact of internal factors (in particular the impact of users), it was suggested to further narrow down the scope of the input data to an hour (e.g., 10–14 in multi-family residential buildings). During these hours, the impact on users was minimized as most of them were outside the building.

1 October 2026 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
PDF file
MWMagda Wlazło
Magda Wlazło
AMAgnieszka Malec
Agnieszka Malec
DMDariusz Majerek
Dariusz Majerek
Anton TrníkAnton Trník
Anton Trník
Jarosław ZubrzyckiJarosław Zubrzycki
Jarosław Zubrzycki
Zbigniew SuchorabZbigniew Suchorab
Zbigniew Suchorab
The objective of this study is to estimate the concentration of selected microbial volatile organic compounds (mVOCs), namely ethylbenzene, cumene, and limonene, using multi-sensor gas arrays combined with statistical regression and machine learning methods. Two sensor array configurations were...