This paper reports the sensitivity of the thermal and the displacement histories predicted by a finite element analysis to material properties and boundary conditions of a directed-energy deposition of a M4 high speed steel thin-wall part additively manufactured on a 42CrMo4 steel substrate. The model accuracy was assessed by comparing the simulation results with the experimental measurements such as evolving local temperatures and distortion of the substrate. The numerical results of thermal history were successfully correlated with the solidified microstructures measured by scanning electron microscope technique, explaining the non-uniform, cellular-type grains depending on the deposit layers. Laser power, thermal conductivity, and thermal capacity of deposit and substrate were considered in the sensitivity analysis in order to quantify the effect of their variations on the local thermal history, while Young’s modulus and yield stress variation effects were evaluated on the distortion response of the sample. The laser power showed the highest impact on the thermal history, then came the thermal capacity, then the conductivity. Considering distortion, variations of the Young’s modulus had a higher impact than the yield stress.
8 September 2022 in International Journal of Mechanical Sciences
The microstructure directly influences the subsequent mechanical properties of materials. In the manufactured parts, the elaboration processes set the microstructure features such as phase types or the characteristics of defects and grains. In this light, this article aims to understand the evolution of the microstructure during the directed energy deposition (DED) manufacturing process of Ti6Al4V alloy. It sets out a new concept of time-phase transformation-block (TTB). This innovative segmentation of the temperature history in different blocks allows us to correlate the thermal histories computed by a 3D finite element (FE) thermal model and the final microstructure of a multilayered Ti6Al4V alloy obtained from the DED process. As a first step, a review of the state of the art on mechanisms that trigger solid-phase transformations of Ti6Al4V alloy is carried out. This shows the inadequacy of the current kinetic models to predict microstructure evolution during DED as multiple values are reported for transformation start temperatures. Secondly, a 3D finite element (FE) thermal simulation is developed and its results are validated against a Ti6Al4V part representative of repair technique using a DED process. The building strategy promotes the heat accumulation and the part exhibits heterogeneity of hardness and of the nature and the number of phases. Within the generated thermal field history, three points of interest (POI) representative of different microstructures are selected. An in-depth analysis of the thermal curves enables distinguishing solid-phase transformations according to their diffusive or displacive mechanisms. Coupled with the state of the art, this analysis highlights both the variable character of the critical points of transformations, and the different phase transformation mechanisms activated depending on the temperature value and on the heating or cooling rate. The validation of this approach is achieved by means of a thorough qualitative description of the evolution of the microstructure at each of the POI during DED process. The new TTB concept is thus shown to provide a flowchart basis to predict the final microstructure based on FE temperature fields.
The aim of this work is to present an efficient procedure for growing large metallic single crystals that associates a classical growth technique (namely, the critical strain-annealing—CSA—method) with advanced methods of accurate full-field strain measurements based on digital image correlation (DIC) technique and of sample geometry design using finite element analysis. Measuring the critical plastic strains with an accuracy better than 0.1% resulted in a significantly improved construction of the recrystallization diagram. Applying this “DIC-assisted CSA method” to an A1050 commercially pure aluminum allowed obtaining in less than two days (26 h to 30 h) large multi-crystal samples with a half dozen of large grains. Their length between 35 mm and 100 mm was in full agreement with the obtained recrystallization diagram.
In finite element models (FEMs), two- or three-dimensional Representative Volume Elements (RVEs) based on a statistical distribution of particles in a matrix can predict mechanical material properties. This article studies an alternative to 3D RVEs with a 2.5D RVE approach defined by a one-plane layer of 3D elements to model the material behavior. This 2.5D RVE relies on springs applied in the out-of-plane direction to constrain the two lateral deformations to be compatible, with the goal of achieving the isotropy of the studied material. The method is experimentally validated by the prediction of the tensile stress–strain curve of a bi-phasic microstructure of the AlSi10Mg alloy. Produced by additive manufacturing, the sample material becomes isotropic after friction stir processing post treatment. If a classical plane strain 2D RVE simulation is clearly too stiff compared to the experiment, the predictions of the stress–strain curves based on 2.5D RVE, 2D RVE with no transversal constraint (called 2D free RVE), and 3D RVE simulations are close to the experiments. The local stress fields within a 2.5D RVE present an interesting similarity with 3D RVE local fields, but differences with the 2D free RVE local results. Since a 2.5D RVE simplifies one spatial dimension, the simulations with this model are faster than the 3D RVE (factor 2580 in CPU or taking into account an optimal parallel computation, a factor 417 in real time). Such a discrepancy can affect the FEM2 multi-scale simulations or the time required to train a neural network, enhancing the interest in a 2.5D RVE model.