The article presents the standard method of the evaluation of car drivers’ psychomotor reaction times. A characteristic feature of this method is the ability to conduct tests using real vehicles equipped with mobile measuring apparatus. Measurements are carried out on people whose task is to initiate specific maneuvers (such as: a braking or turning maneuver, a combined braking and turning maneuver, as well as e.g., the use of an audio signal) in response to external stimuli coming from different directions. The sources of the stimuli are light signals emitted by variable message signs placed around the vehicle. The developed control and measurement equipment allows us to realize various and complex test scenarios. It generates stimulus sequences, assesses the correctness of the driver’s response and measures its time. This method allows us to obtain sets of results from tests carried out under different conditions and variable test durations. The possibility of testing a large number of participants in a relatively short time and in repetitive conditions allows for reliable statistical inference. The paper presents examples of research results obtained on the basis of few thousand tests carried out on a large group of respondents. The registered data was statistically processed and referred to the literature. A high degree of correlation between the analyzed results and the literature reports proves that the presented method may be a source of data for the analysis of phenomena related to the time of the driver’s response, especially the influence of various factors affecting its values.
The use of road simulators in vehicle durability tests enables a significant reduction in time related to the implementation of a new product. However, there is still a need to improve the methods of these tests in order to obtain a full correlation between the time of the tests on the simulator with respect to the mileage of the vehicle in real road conditions. The aim of this work is a validation and improvement of the durability testing method for large-sized vehicles. Comparative tests of shock absorbers dismantled from semi-trailers with different mileage and shock absorbers dismantled from semi-trailers after durability tests conducted at the MTS test bench are presented. The relationship between the maximum damping force and the displacement speed of the shock absorber piston was examined. Additionally, the influence of the shock absorber temperature on the damping force was analyzed. As a result of the tests, the dynamic characteristics of the shock absorbers were determined and the relationship between the maximum damping force and the mileage of the trailers was determined. It was found that the load on the trailers during their operation has a significant impact on the change in the characteristics of the shock absorbers. What is new in this publication is the validation of the methodology for conducting durability tests previously proposed by the authors based on the selected component, which is the shock absorber. The authors have not yet encountered in the literature any attempt to validate the methodology for conducting durability tests for large-sized vehicles.
The article describes an assessment of possible changes in constant fatigue life of a medium flow-coefficient centrifugal compressor impeller subject to operation at close-to-surge point. Some aspects of duct acoustics are additionally analyzed. The experimental measurements at partial load are presented and are primarily used for validation of unidirectionally coupled fluid-structural numerical model. The model is based on unsteady finite-volume fluid-flow simulations and on finite-element transient structural analysis. The validation is followed by the model implementation to replicate the industry-scale loads with reasonably higher rotational speed and suction pressure. The approach demonstrates satisfactory accuracy in prediction of stage performance and unsteady flow field in vaneless diffuser. The latter is deduced from signal analysis relying on continuous wavelet transformations. On the other hand, it is found that the aerodynamic incidence losses at close-to-surge point are underpredicted. The structural simulation generates considerable amounts of numerical noise, which has to be separated prior to evaluation of fluid-induced dynamic strain. The main source of disturbance is defined as a stationary region of static pressure drop caused by flow contraction at volute tongue and leading to first engine-order excitation in rotating frame of reference. Eventually, it is concluded that the amplitude of excitation is too low to lead to any additional fatigue.
This article describes the conducted examinations of five different prototype shock absorbers. The differences resulted from deliberate modifications to their components. The tests were divided into five series of measurements, each involving testing five identical shock absorber designs. The authors assessed the repeatability and process capability of the production process for each shock absorber design. The study also aimed to identify factors that could lead to undesirable variations in the shock absorber’s dynamic parameters, such as damping force, the shape of the force–displacement characteristic, differences in the system’s response during compression and rebound, and the variability of the response depending on the piston’s speed. The results were then analyzed by using various research methods, among which the most important is the SPC (Statistical Process Control) method. Furthermore, statistical results, such as Cp, Cpk, stability graphs, and process repeatability, are presented.