In this work, the problem of reducing the energy consumption of the cooling circuit for the propulsion system of an all-electric vehicle is approached with two different concepts: improvement of the powertrain efficiency and optimization of the control strategy. Improvement of the powertrain efficiency is obtained through a modular design, which consists of replacing the electric powertrain with several smaller traction modules whose powers sum up to the total power of the original powertrain. In this paper, it is shown how modularity, among other benefits, also allows reducing the energy consumption of the cooling system up to 54%. The energy consumption of the cooling system is associated with two components: the pump and the fan. They produce a so-called auxiliary load on the battery, reducing the maximum range of the vehicle. In conventional cooling systems, the pump and the fan are controlled with a thermostat, without taking into account the energy consumption. Conversely, in this work a control strategy to reduce the auxiliary loads is developed and compared with the conventional approach, showing that the energy consumption of the cooling system can be reduced up to 27%. To test the control strategy, numerical simulations have been carried out with a 1-D model of the cooling system. On the other hand, all the thermal loads of the components have been calculated with a vehicle simulator, which is able to predict the vehicle’s behavior under different driving cycles.
Efficient and low-polluting mobility is a major demand in all countries. Hybrid electric vehicles have already shown to be suitable to respond to this need, being a reliable alternative to conventional cars, at least in urban environments. Nevertheless, such vehicles present a yet unexplored potential. In this paper, we will investigate how the powertrain efficiency may possibly benefit, in an integrated drivetrain for a hybrid electric vehicle, based on a turbocharged gasoline engine, of an innovative supercharging system. The compressor and turbine will be mechanically decoupled so as to independently optimize their operation, avoiding turbo lag and maximizing energy recovery by completely eliminating the waste-gate valve. This, in turns, requires changing the turbine so as to have a flattest possible efficiency/load curve. Therefore, an ad-hoc designed turbine will be implemented in the decoupled configuration, to be used to drive an electrical generator and produce electrical energy for charging the battery. This study presents a preliminary assessment of the potential of a turbo-compounded system for a 1L turbocharged gasoline engine for a small city car. To this aim, a one-dimensional dynamic model of the engine has been built in GT-Suite and has been calibrated and validated by means of experimental data obtained on a dynamometer, both in steady state and dynamic conditions. In particular, the model has been calibrated by means of experimental data obtained in stationary conditions and its robustness has then been verified through experimental data obtained under transient conditions. The model also includes data retrieved from the characterization of the existing turbine and compressor, while a new performance map for the turbine has been designed to better exploit the potential of the components’ decoupling. Results include the estimation of energy recovery potential of such a solution. Under the implementation of a straightforward control strategy, which runs both compressor and turbine at the same speed, the system is able to achieve a 60.57% increase in energy recovered from the exhaust gasses in the turbine. Afterwards, an attempt was made to limit the minimum turbine speed to 45000 rpm and simultaneously decrease the instantaneous speed by 3000 rpm compared to the compressor, attaining a further increase of 1.7% in the energy recovered by the turbine.
8 September 2013 in SAE International Journal of Advances and Current Practices in Mobility
Flame luminosity fields can nowadays be collected from optically accessible engines, with high spatial and temporal resolution, and constitute a very powerful investigation means for the transient combustion phenomena taking place in the engine chamber. Interpretation of the impressive amount of collected data can be quite challenging, mainly due to the variety of coupled phenomena involved. Application of Independent Component Analysis (ICA) aims here at separating spatial structures related to different combustion events, and is coupled with the analysis of the statistics of the coefficients of the independent components, and of the measured in-cylinder parameters. This paper reports on the comparison of the application of ICA to 2D images of combustion-related luminosity collected from two different optically accessible engines: Diesel and spark ignition. Independent components and their coefficients are first extracted from sets of luminosity images, and then used to identify leading structures and to study the transient behavior of the combustion process. The two components identified from the single Diesel cycle appear to be clearly related to early combustion along the fuel jets and later combustion near the bowl walls, respectively; quantitative analysis of coefficient statistics confirms the lower variability of the jet flames with respect to combustion near the chamber walls. The same can be said of the results of the analysis for SI combustion images, which are separated in early, median and final luminous combustion. The analysis is fast and reliable and can be prospectively applied to many different optical engine configurations.
10 February 2026 in Energy Conversion and Management