Andrea La Gala

Mr. Andrea La Gala

Centre for Polymer and Material Technologies

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 November 2020 in Processes
Verified
Journal Article
Open access
PDF file
AGAndrea La Gala
Andrea La Gala
RFRudinei Fiorio
Rudinei Fiorio
MEMustafa Erkoç
Mustafa Erkoç
Ludwig CardonLudwig Cardon
Ludwig Cardon
Dagmar R. D'hoogeDagmar R. D'hooge
Dagmar R. D'hooge
One of the challenges for single-screw micro-extrusion or additive manufacturing (AM), thus 3D printing, of polymers is controlling the melting efficiency so that energy and equipment costs can be minimized. Here, a numerical model is presented for AM process design, selecting acrylonitrile–butadiene–styrene (ABS) as viscoelastic reference polymer. It is demonstrated that AM melting is different compared to conventional melting due to variation in extrusion dimensions, leading to a different balance in heating by conduction and viscous heat dissipation as caused by the shearing between the melt layers in the associated film layer near the barrel. The thickness of this melt film layer is variable along the screw length, and it is shown that simplified models assuming an overall average value are too approximate. It is highlighted that the screw frequency, pitch angle and compression ratio are important process parameters to control the point of melt finalization. In addition, the power-law index reflecting the shear thinning nature of the polymer melt is showcased as a key parameter. Moreover, AM process results assuming constant and temperature dependent specific heat capacities and thermal conductivities are compared. The current work opens the door for on-line AM process control, addressing all relevant operating and material parameters.

22 November 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
DCDaniel Victor Amaral Ceretti
Daniel Victor Amaral Ceretti
YMYoshi W. Marien
Yoshi W. Marien
MEMariya Edeleva
Mariya Edeleva
AGAndrea La Gala
Andrea La Gala
Ludwig CardonLudwig Cardon
Ludwig Cardon
Dagmar R. D'hoogeDagmar R. D'hooge
Dagmar R. D'hooge
An important polymer processing technique is additive manufacturing (AM), which enables shape-free design of complex final parts with limited waste during the development change, at least if the impact of molecular degradation reactions is minimized. In the present work, polystyrene (PS) and acrylonitrile butadiene styrene (ABS) polymer have been processed via: (i) fused filament fabrication (FFF), separately accounting for the prior single screw extrusion (SSE) filament production; and (ii) pellet-based additive manufacturing (PBAM), which are two important AM techniques. The influence of printing temperature, layer thickness, printing velocity, and printing technique on the degradation of both polymeric materials is studied by means of thermogravimetric analysis (TGA), size exclusion chromatography (SEC), small amplitude oscillatory shearing tests (SAOS), Fourier-transform infrared spectroscopy (FTIR), and yellowness index (YI) measurements. For ABS, SSE-FF leads to more fission (higher mechanical loading) whereas PBAM results in more cross-linking (more thermal loading). For PS, fission is always dominant and this more evident under FFF conditions. ABS also exhibits yellowing upon processing, indicating thermo-oxidative degradation although below the FTIR sensitivity limit. The selected PBAM conditions with PS are already delivering printed specimens with good mechanical properties and lower degradation. For ABS, a further PBAM optimization is still desired compared to the FFF countercase, taking into account layer-by-layer adhesion.

25 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
AGAndrea La Gala
Andrea La Gala
RFRudinei Fiorio
Rudinei Fiorio
DCDaniel Victor Amaral Ceretti
Daniel Victor Amaral Ceretti
MEMustafa Erkoç
Mustafa Erkoç
Ludwig CardonLudwig Cardon
Ludwig Cardon
Dagmar R. D'hoogeDagmar R. D'hooge
Dagmar R. D'hooge
To improve the product quality of polymeric parts realized through extrusion-based additive manufacturing (EAM) utilizing pellets, a good control of the melting is required. In the present work, we demonstrate the strength of a previously developed melt removal using a drag framework to support such improvement. This model, downscaled from conventional extrusion, is successfully validated for pellet-based EAM—hence, micro-extrusion—employing three material types with different measured rheological behavior, i.e., acrylonitrile-butadiene-styrene (ABS), polylactic acid (PLA) and styrene-ethylene-butylene-styrene polymer (SEBS). The model’s validation is made possible by conducting for the first time dedicated EAM screw-freezing experiments combined with appropriate image/data analysis and inputting rheological data. It is showcased that the (overall) processing temperature is crucial to enable similar melting efficiencies. The melting mechanism can vary with the material type. For ABS, an initially large contribution of viscous heat dissipation is observed, while for PLA and SEBS thermal conduction is always more relevant. It is highlighted based on scanning electron microscopy (SEM) analysis that upon properly tuning the finalization of the melting point within the envisaged melting zone, better final material properties are achieved. The model can be further used to find an optimal balance between processing time (e.g., by variation of the screw frequency) and material product performance (e.g., strength of the printed polymeric part).